2012 Yamaha Motorsports RS Venture Owners Manual - Page 97

2012 Yamaha Motorsports RS Venture Manual

Get 2012 Yamaha Motorsports RS Venture PDF manuals and user guides View all 2012 Yamaha Motorsports RS Venture manuals

Page 97 highlights

Periodic maintenance and adjustment 9. Tighten the V-belt position adjusting bolts. V-belt position adjusting bolt tightening torque: 10 Nm (1.0 m·kgf, 7.2 ft·lbf) 10. Install the V-belt over the primary sheave assembly. 11. Rotate the secondary sliding sheave clockwise and push it so that it separates from the secondary fixed sheave. RS90P / RS90PLT / RST90PGT 1 1. Left lower cover 14. Install the drive guard, and then install the left side cover and the shroud (RS90P / RS90PLT / RST90PGT), or close the shroud (RST90). ESU13923 Drive chain housing To check the drive chain housing oil level 1. 1. Secondary sliding sheave 2. Secondary fixed sheave 2. 12. Install the V-belt between the secondary sliding and fixed sheaves. 3. Place the snowmobile on a level surface and apply the parking brake. Remove the shroud and the right side cover (RS90P / RS90PLT / RST90PGT), or open the shroud (RST90). [See page 63 (RS90P / RS90PLT / RST90PGT) or page 67 (RST90) for the procedures.] Remove the dipstick, wipe it off with a clean rag, and then insert it back into the filler hole. RS90P / RS90PLT / RST90PGT 1 1. V-belt 13. Place the left lower cover in the original position, and then install the screws and the bolts. (RS90P / RS90PLT / RST90PGT). 1. Dipstick 91

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Periodic maintenance and adjustment
91
9.
Tighten the V-belt position adjusting
bolts.
10.
Install the V-belt over the primary sheave
assembly.
11. Rotate the secondary sliding sheave
clockwise and push it so that it separates
from the secondary fixed sheave.
12.
Install the V-belt between the secondary
sliding and fixed sheaves.
13.
Place the left lower cover in the original
position, and then install the screws and
the
bolts.
(RS90P /
RS90PLT /
RST90PGT).
RS90P / RS90PLT / RST90PGT
14.
Install the drive guard, and then install the
left side cover and the shroud (RS90P /
RS90PLT / RST90PGT), or close the
shroud (RST90).
ESU13923
Drive chain housing
To check the drive chain housing oil
level
1.
Place the snowmobile on a level surface
and apply the parking brake.
2.
Remove the shroud and the right side
cover (RS90P / RS90PLT / RST90PGT),
or open the shroud (RST90). [See page
63 (RS90P / RS90PLT / RST90PGT) or
page 67 (RST90) for the procedures.]
3.
Remove the dipstick, wipe it off with a
clean rag, and then insert it back into the
filler hole.
RS90P / RS90PLT / RST90PGT
V-belt position adjusting bolt tightening
torque:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
1.
Secondary sliding sheave
2.
Secondary fixed sheave
1. V-belt
1.
Left lower cover
1. Dipstick
1
1