2014 Ducati Streetfighter 848 Owners Manual - Page 55

2014 Ducati Streetfighter 848 Manual

Page 55 highlights

DDA data acquisition This function allows activating the DDA (Ducati Data Analyzer) (ref. page 110): data logger must be connected to vehicle wiring. To enable this function, enter the menu and set the "DDA" data acquisition to "On" by holding the RESET button (14, fig. 14) pressed for 3 seconds. As a confirmation that the function is active, the (small ) DDA text is turned on and will remain always visible even outside the menu. The START/STOP control for the data logger lap separator is the high-beam flash button FLASH (13, fig. 14) on the LH switch. If the DDA function is active and the instrument panel is suddenly switched off (Key-Off), the function is switched off automatically. Note Online assistance is available to Ducati Data Analyzer (DDA) owners (http://dda.prosa.com). This service will provide anything necessary to correctly use the DDA with your PC: both for the device and the software for analyzing the recorded data. Warning After use, disconnect the DDA from the main wiring harness. 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151

54
DDA data acquisition
This function allows activating the DDA (Ducati Data
Analyzer) (ref. page 110): data logger must be
connected to vehicle wiring.
To enable this function, enter the menu and set the
“DDA“ data acquisition to “On“ by holding the
RESET button (14, fig. 14) pressed for 3 seconds.
As a confirmation that the function is active, the
(small ) DDA text is turned on and will remain always
visible even outside the menu.
The START/STOP control for the data logger lap
separator is the high-beam flash button FLASH (13,
fig. 14) on the LH switch.
If the DDA function is active and the instrument panel
is suddenly switched off (Key-Off), the function is
switched off automatically.
Note
Online assistance is available to Ducati Data
Analyzer (DDA) owners (http://dda.prosa.com). This
service will provide anything necessary to correctly
use the DDA with your PC: both for the device and
the software for analyzing the recorded data.
Warning
After use, disconnect the DDA from the main
wiring harness.