2014 Ducati Streetfighter 848 Owners Manual - Page 52

2014 Ducati Streetfighter 848 Manual

Page 52 highlights

LAP timer This function describes the lap time display. To enable this function, enter the menu and set the LAP function to "On" by holding RESET button (14, fig. 14) pressed for 3 seconds. The lap timer is started and stopped using the highbeam flasher button FLASH (13, fig. 14) on the LH switch. When the LAP function is active, each time you press the FLASH button, the instrument panel will display the lap time for 10 seconds, before reverting to normal mode. You can save a maximum of 30 laps in the memory. Once the memory is full, the dashboard no longer stores lap times when the FLASH headlight button is pressed, and the flashing message "FULL" is shown on the display for 3 seconds until the times are reset. Press RESET for 3 sec. Press RESET for 3 sec. fig. 31 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151

51
LAP timer
This function describes the lap time display.
To enable this function, enter the menu and set the
LAP function to “On“ by holding RESET button (14,
fig. 14) pressed for 3 seconds.
The lap timer is started and stopped using the high-
beam flasher button FLASH (13, fig. 14) on the LH
switch.
When the LAP function is active, each time you press
the FLASH button, the instrument panel will display
the lap time for 10 seconds, before reverting to
normal mode.
You can save a maximum of 30 laps in the memory.
Once the memory is full, the dashboard no longer
stores lap times when the FLASH headlight button is
pressed, and the flashing message “FULL” is shown
on the display for 3 seconds until the times are reset.
fig. 31
Press RESET for 3 sec.
Press RESET for 3 sec.