Home » Rane Manuals » Audio Components » Rane HAL1x » Manual Viewer

Rane HAL1x Design Guide - Page 139

these functions.

Add to My Manuals
Save this manual to your list of manuals

Page 139 highlights

CHAPTER 3: Key Audio Design Features 6. What is the layout of the rooms in your room combine? Open the Room Combine Processor block and configure the layout of the rooms as well as which walls are movable. 7. Do you need to customize the audio processing in one or more rooms? Open the relevant Room Processors to do so. In reality, you could stop here and have a functioning room combine system. But it's likely you will want to configure remote control of the room configuration and you may also want to customize the processing for each possible room. Open the Room Combine Processor properties dialog to perform these functions. 8. Do you want to change any blocks outside of the Room Combine Processor when rooms are activated? Set up the PEQ blocks, output blocks, and any other blocks you want to associate with the room. Add these blocks to the room's main preset. 135

Section	Page
CHAPTER 1: Welcome to the World of HAL	5
About This Document	5
System Requirements	7
Minimum Requirements for Running Halogen	7
Recommendations for Best Performance	7
Administrative Rights Requirements	8
Using the HAL System Documentation	8
Getting Started	10
CHAPTER 2: Introduction to the HAL System	12
Overview of HAL Devices	15
Available HAL Models	15
HAL Front and Rear Panels	16
Discontinued HAL Models	22
Remote Audio Devices	25
How the shielded CAT 5e Cabling is Utilized	25
RAD Grounding	26
The Parts of a RAD	28
PAGER1 RAD	30
RAD16z	31
AM1 and AM2 RADs	34
RAD26 - One Room RAD	35
RAD27 - USB Audio	41
Using a RAD as a Portable Device	45
Discontinued RAD Models	47
Digital Remote Devices	47
DR Grounding	48
Available Digital Remote Models	48
Infrared Remote Devices	65
IR2 Device	65
Expansion Units	67
HAL1x Expansion Units	68
Discontinued EXP Models	89
Momentary and Latching Toggle Configuration	89
Introduction to the Halogen Software	92
Basic Structure	93
Workspace Layout	94
HAL System Connectivity	95
Required Ports	95
Required Processes	96
CHAPTER 3: Key Audio Design Features	98
About the Distributed Program Bus	98
About Zone Processing	100
About Paging	103
About Control Links	110
Basics of Control Linking	110
Advanced Topics	118
Best Practices	124
About Room Combine	126
About Presets	140
About Events	153
About Control Pages	158
Basics of Control Pages	158
Advanced Topics	165
Best Practices	166
CHAPTER 4: Designing and Installing Your HAL System	169
Recommended Workflow for Creating a HAL System	169
A Few Design and Installation Tips	172
Installing and Starting the Halogen Software	172
About Halogen Configuration Files	174
Creating, Viewing, and Modifying Notes about a HAL System Configuration	177
Generating Device Labels	178
Generating Hardware Lists	180
Upgrading Halogen Software and HAL Firmware	180
Uninstalling the Halogen Software	182
APPENDIX A: Transitioning from Drag Net	183
Index	186

Match case Limit results 1 per page

What is the layout of the rooms in your room combine? Open the Room Combine Processor block

and configure the layout of the rooms as well as which walls are movable.

Do you need to customize the audio processing in one or more rooms? Open the relevant Room Proc-

essors to do so.

In reality, you could stop here and have a functioning room combine system. But it's likely you will

want to configure remote control of the room configuration and you may also want to customize the

processing for each possible room. Open the Room Combine Processor properties dialog to perform

these functions.

Do you want to change any blocks outside of the Room Combine Processor when rooms are acti-

vated? Set up the PEQ blocks, output blocks, and any other blocks you want to associate with the

room. Add these blocks to the room's main preset.

CHAPTER 3: Key Audio Design Features

135