Panasonic PT-EW550 PT-EZ590 Series Operating Instructions - Page 109

[digital Link Menu], [wired Lan], [projector Name], English - 109

Get Panasonic PT-EW550 PDF manuals and user guides View all Panasonic PT-EW550 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 109 highlights

Chapter 4 Settings - [NETWORK] menu [SIGNAL QUALITY] [SIGNAL QUALITY] is a numerical value of the amount of error, and the display color changes to green, yellow, or red depending on that value. Check the signal quality level while receiving a signal from the twisted-pair-cable transmitter. ff MAX/MIN: Maximum/minimum value of the amount of error. ff Green (-12 dB or lower) → Normal signal quality level. ff Yellow (-11 to -8 dB) → Warning level where there is the possibility of noise introduced on the screen. ff Red (-7 dB or higher) → Abnormal level where synchronization may be interrupted or a signal may not be received. [DIGITAL LINK MENU] (Only for PT‑EZ590, PT‑EW650 and PT‑EX620) When the optional DIGITAL LINK output supported device (Model No.: ET‑YFB100G, ET‑YFB200G) is connected to the terminal, the main menu of DIGITAL LINK output supported device is displayed. Refer to the Operating Instructions of the DIGITAL LINK output supported device for details. Note ff When [NETWORK] menu → [NETWORK CONTROL] → [EXTRON XTP] is set to [ON], [DIGITAL LINK MENU] cannot be selected. [WIRED LAN] You can make detailed wired LAN settings. 1) Press as to select [WIRED LAN]. 2) Press the button. ffThe [WIRED DETAILED SETUP] screen is displayed. 3) Press as to select an item, and change the setting according to the instructions. [DHCP] [IP ADDRESS] [SUBNET MASK] [DEFAULT GATEWAY] [DNS1] [DNS2] [ON] If a DHCP server exists in the network to which the projector is connected, the IP address will automatically be acquired. [OFF] If a DHCP server does not exist in the network to which the projector is connected, additionally set [IP ADDRESS], [SUBNET MASK] and [DEFAULT GATEWAY]. Enter the IP address if DHCP server is not used. Enter the subnet mask if DHCP server is not used. Enter the gateway address if DHCP server is not used. Enter the preferred DNS server address if DHCP server is not used. Enter the alternate DNS server address if DHCP server is not used. 4) Press as to select [OK], and press the button. rrDefault settings of [WIRED LAN] ffThe following settings are set before the projector leaves the factory. [DHCP] OFF [IP ADDRESS] 192.168.10.100 [SUBNET MASK] 255.255.255.0 [DEFAULT GATEWAY] 192.168.10.1 [DNS1]/[DNS2] NONE Note ff Before using the DHCP server, make sure the DHCP server is already functioning. ff Consult your network administrator regarding the IP ADDRESS, SUBNET MASK and DEFAULT GATEWAY. ff The settings of network are same for both the terminal and the terminal. [PROJECTOR NAME] Change the name as desired in such a case as the projector needs to be identified on application software. 1) Press as to select [PROJECTOR NAME]. ENGLISH - 109

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
Chapter 4
Settings — [NETWORK] menu
ENGLISH - 109
[SIGNAL QUALITY]
[SIGNAL QUALITY] is a numerical value of the amount of error, and the display color changes to
green, yellow, or red depending on that value.
Check the signal quality level while receiving a signal from the twisted-pair-cable transmitter.
f
MAX/MIN: Maximum/minimum value of the amount of error.
f
Green (
-
12 dB or lower)
→
Normal signal quality level.
f
Yellow (
-
11 to
-
8 dB)
→
Warning level where there is the possibility of noise introduced on the
screen.
f
Red (
-
7 dB or higher)
→
Abnormal level where synchronization may be interrupted or a signal may
not be received.
[DIGITAL LINK MENU]
(Only for PT-EZ590, PT-EW650 and PT-EX620)
When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected
to the <DIGITAL LINK/LAN> terminal, the main menu of DIGITAL LINK output supported device is displayed.
Refer to the Operating Instructions of the DIGITAL LINK output supported device for details.
Note
f
When [NETWORK] menu → [NETWORK CONTROL] → [EXTRON XTP] is set to [ON], [DIGITAL LINK MENU] cannot be selected.
[WIRED LAN]
You can make detailed wired LAN settings.
1)
Press
as
to select [WIRED LAN].
2)
Press the <ENTER> button.
f
The
[WIRED DETAILED SETUP]
screen is displayed.
3)
Press
as
to select an item, and change the setting according to the instructions.
[DHCP]
[ON]
If a DHCP server exists in the network to which the
projector is connected, the IP address will automatically be
acquired.
[OFF]
If a DHCP server does not exist in the network to which
the projector is connected, additionally set [IP ADDRESS],
[SUBNET MASK] and [DEFAULT GATEWAY].
[IP ADDRESS]
Enter the IP address if DHCP server is not used.
[SUBNET MASK]
Enter the subnet mask if DHCP server is not used.
[DEFAULT GATEWAY]
Enter the gateway address if DHCP server is not used.
[DNS1]
Enter the preferred DNS server address if DHCP server is not used.
[DNS2]
Enter the alternate DNS server address if DHCP server is not used.
4)
Press
as
to select [OK], and press the <ENTER> button.
r
Default settings of [WIRED LAN]
f
The following settings are set before the projector leaves the factory.
[DHCP]
OFF
[IP ADDRESS]
192.168.10.100
[SUBNET MASK]
255.255.255.0
[DEFAULT GATEWAY]
192.168.10.1
[DNS1]/[DNS2]
NONE
Note
f
Before using the DHCP server, make sure the DHCP server is already functioning.
f
Consult your network administrator regarding the IP ADDRESS, SUBNET MASK and DEFAULT GATEWAY.
f
The settings of network are same for both the <LAN> terminal and the <DIGITAL LINK/LAN> terminal.
[PROJECTOR NAME]
Change the name as desired in such a case as the projector needs to be identified on application software.
1)
Press
as
to select [PROJECTOR NAME].