Panasonic AJ-HPX3100GJ Operating Instructions - Page 80
Chromatic aberration, compensation, System information, and warnings, Time code indication, Extender
View all Panasonic AJ-HPX3100GJ manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 80 highlights
Information Item 13. System information and warnings Indication SYSTEM ERROR-¢¢ TURN POWER OFF CARD ERR ¢ REC WARNING OVER MAX# CLIPS TEMPORARY PAUSE BACKUP BATT EMPTY FAN STOP WIRELESS-RF EOM BOS EOS CANNOT REC CANNOT PLAY COMM ERROR TEXT MEMO TEXT MEMO INVALID MARK ON/OFF SHOT MARK INVALID UPDATING USB DEVICE USB HOST THUMBNAIL OPEN CLIP DISCONTINUED TC REGEN SLOT SELECT SLOT SELECT INVALID DIR NG CARD SLOT1/2 RUN DOWN CARD SLOT1/2 REAR XR AUTO 14. Time code indication TCG TCR (V)UBG (V)UBR CTL 15. Chromatic aberration CAC compensation 16. Extender EX 17. Color temperature ¢.¢K 12:59:59:20 12:59:59:20 AB CD EF 00 12 34 56 78 -1:59:59:20 18. Filter position 19. Dynamic range stretcher mode 1 - 4 A - D (blink) DRS Status Something abnormal is happening to the internal computer communications or reference signal. No further recording or playback can be performed. ¢¢ is replaced with an error code. For more information, see [Error Codes] (page 155). P2 card has been removed while being accessed (recorded, played back, or formatted), and subsequent operation is disabled. An error has occurred while recording data to or playing data from a P2 card. In the actual indication the ¢ is replaced by the slot number of the P2 card that triggered the error. Something abnormal is happening to video and/or audio being recorded. Displayed when the maximum number of clips (1000) recorded to the P2 card is exceeded. There is a temporary halt in recording due to distortion in reference signals such as during GENLOCK input. Backup battery needs replacing. The fan is locked and halted. RF signal from the wireless receiver is degraded. P2 card has no free space. Playback position is at the start of all the clips. Playback position is at the end of all the clips. The P2 card is not recordable. Detailed information is provided on the FUNCTION screen of MODE CHECK. > [Displays in mode check only] (page 82) Clip cannot be played back perhaps because no P2 card is loaded, or the P2 card contains no clips. Displayed when disconnection between microcomputers continues for a specified period or longer. Text memo has been added. Text memo has not been successfully added. Shot mark been added or deleted. For information on shot marks, see [Shot Mark Function] (page 46). This is displayed when shot marks cannot be added. Clip information is being updated. Playback operation disabled. AJ-HPX3100 is in USB DEVICE mode. When communication is disabled, the indication blinks. Indicates that the camera-recorder is set to the USB HOST mode. When the external hard disk is not successfully recognized, then the indication blinks. Thumbnail is being manipulated. Displayed when the consistency of the combined clip is disrupted and subsequent recordings cannot be combined in the clip when recording in ONE CLIP REC mode. The RET button was pressed to regenerate the time code as the time code for the last clip recorded on a P2 card. This blinks while the recording slots of P2 cards are switched after pressing the USER switch where the SLOT SEL function is assigned. This is displayed if the recording slots of P2 cards cannot be switched when the USER switch where the SLOT SEL function is assigned is pressed. This is displayed when the recording starts or completes while a P2 card with an irregular directory arrangement is inserted or data are recorded after inserting an irregular P2 card. This is displayed when the recording starts or completes with a P2 card on which the maximum number of overwrites has been exceeded, or when data is recorded after inserting such a P2 card. The AUDIO IN switch is disabled because audio input automatically goes to the rear XLR connector. TCG (time code generator value) TCR (time code reader value) UBG VUBG (User bits generator value) UBR VUBR (User bits reader value) Displays CTL count. Displayed when chromatic aberration compensation is activated Lens extender used. Color temperature assigned to A, B, and PRST of the WHITE BAL switch (this is a value stored at AWB performance or a value set through the menu option). The indication is not provided in ATW mode. This indicates the position of the ND filter. This indicates the position of the CC filter. This indicates that the filter has not been set to a proper position. This appears when the video level of a part with high brightness is compressed, and the function stretching the dynamic range is selected. 80 Adjustments and Settings for Recording : Viewfinder Screen Status Displays