Panasonic AJ-HPX3100GJ Operating Instructions - Page 154
Image Sequence Error, Corruption of Standard Signal, Recording Error, Number of Clips Exceeded
View all Panasonic AJ-HPX3100GJ manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 154 highlights
5. Image Sequence Error Display window indication WARNING lamp Tally lamp Viewfinder Warning tone "E-40" appears in the time code display field. Blinks 4 times per second. Blinks 4 times per second while recording continues. The REC WARNING indicator lights up. Beeps 4 times per second. Warning description There are abnormal conditions in the image sequence of the 24P, 30P, or 25P mode. Recording/ playback operation Images can be recorded and played back, but some frames may be dropped or the sequences of TC and UB may shift. Confirm the recording/playback operation after turning OFF the power supply once and Countermeasures then turning it on again. If the error is not corrected after executing this procedure, contact the dealer. 6. Corruption of Standard Signal Display window "E-40" appears in the time code display field. indication WARNING lamp Blinks 4 times per second. Tally lamp Blinks 4 times per second. Viewfinder The TEMPORARY PAUSE indicator lights up. Warning tone Beeps 4 times per second while recording continues. Warning description Corruption in the input signals from the standard GENLOCK IN and SDI IN connectors means correct recording is not possible, and this has stopped. The clip will be divided. Recording/ playback operation When the signal returns to normal, recording will automatically start again. However, this will not automatically start when in INTERVAL REC mode or LOOP REC mode. Please check the input signal from the Countermeasures GENLOCK IN connector or SDI IN connector. If errors continue, please contact your dealer. 7. Recording Error Display window indication WARNING lamp Tally lamp "00:00:00:11" appears in the time code display field. Even after recording is stopped, this display continues to blink until the next operation is performed. Blinks 4 times per second while recording continues. Blinks 4 times per second while recording continues. Viewfinder The REC WARNING indicator lights up. Warning tone Beeps 4 times per second while recording continues. Warning description This indicates a failure either in the P2 card recording or the recording circuit. Recording/ playback operation The recording may stop or continue. Restart recording. Or, turn the power OFF and Countermeasures turn it ON again, before starting recording. If the recording cannot be performed normally, change the P2 card. 8. Number of Clips Exceeded Display window indication WARNING lamp Tally lamp "00:00:00:11" appears in the time code display field. Even after recording is stopped, this display continues to blink until the next operation is performed. Blinks 4 times per second while recording continues. Blinks 4 times per second while recording continues. Viewfinder The OVER MAX# CLIPS indicator lights up. Warning tone Warning description Beeps 4 times per second while recording continues. This is displayed when attempting to record clips where the total quantity exceeds the upper limit (1000 pieces) for a single P2 card. Recording/ playback operation Cannot record. Stops while recording. Countermeasures Insert a new P2 card or delete the clips in the P2 card. unwanted 9. Low Wireless Signal Reception Display window indication WARNING lamp Tally lamp Viewfinder Warning tone Warning description No display. Blinks 4 times per second. (During pause and recording) Blinks 4 times per second while recording continues. The WIRELESS RF indicator lights up while recording continues. Beeps 4 times per second while recording continues. This error indicates poor wireless audio reception conditions. Recording/ playback operation Continues to operate without receiving the wireless microphone signal. Countermeasures Check the microphone power supply and the reception status of the wireless receiver. 10. Battery Nearly Empty Display window One of the bars in the battery remaining indication indicator starts blinking. WARNING lamp Blinks once per second. Tally lamp Blinks once per second. Viewfinder The BATT LED blinks. Warning tone Beeps 4 times per second. Warning description The battery is about to run out. Recording/ playback operation Continues to operate. Countermeasures Replace the battery as required. 154 Maintenance and Inspections: Warning System