Marantz HD-AMP1 Owner s Manual in English - Page 57

Power does not turn on / Power is turned off

Get Marantz HD-AMP1 PDF manuals and user guides View all Marantz HD-AMP1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Contents Connections Playback Settings Tips Appendix Troubleshooting 1. Are the connections correct? 2. Is the set being operated as described in the owner's manual? 3. Are the other devices operating properly? If this unit does not operate properly, check the items listed in the table below. Should the problem persist, there may be a malfunction. In this case, disconnect the power immediately and contact your store of purchase. o Power does not turn on / Power is turned off Symptom Cause / Solution Power is not turned on. 0 Check whether the power plug is correctly inserted into the power outlet. 0 This unit is in standby mode. Press the X button on the unit or the POWER X button on the remote control. Power automatically turns off. 0 The Auto Standby mode is on. The Auto Standby mode switches the unit to standby mode when the unit is not operated for approximately 30 minutes. To disable Auto Standby mode, set "AutoStby" on the menu to "Off". Power turns off and the 0 The protection circuit has been activated due to a rise in temperature within this unit. Turn the power off, standby indicator flashes in wait about an hour until this unit cools down sufficiently, and then turn the power on again. red approx. every 2 seconds. 0 Please re-install this unit in a place having good ventilation. Power turns off and the 0 Check the speaker connections. The protection circuit may have been activated because speaker cable standby indicator flashes in red approx. every 0.5 seconds. core wires came in contact with each other or a core wire was disconnected from the connector and came in contact with the rear panel of this unit. After unplugging the power cord, firmly re-twist the core wire, and then reconnect the wire. 0 Turn down the volume and turn on the power again. 0 This unit's amplifier circuit has failed. Unplug the power cord and contact our customer service center. Page 25 27 54 27 － 17 27 － Front panel Display Rear panel 57 Remote Index

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
Troubleshooting
1.
Are the connections correct?
2.
Is the set being operated as described in the owner’s manual?
3.
Are the other devices operating properly?
If this unit does not operate properly, check the items listed in the table below.
Should the problem persist, there may be a malfunction. In this case, disconnect the power immediately and contact your store of purchase.
o
Power does not turn on / Power is turned off
Symptom
Cause / Solution
Page
Power is not turned on.
0
Check whether the power plug is correctly inserted into the power outlet.
25
0
This unit is in standby mode. Press the
X
button on the unit or the POWER
X
button on the remote
control.
27
Power automatically turns
off.
0
The Auto Standby mode is on. The Auto Standby mode switches the unit to standby mode when the unit
is not operated for approximately 30 minutes. To disable Auto Standby mode, set “AutoStby” on the menu
to “Off”.
54
Power turns off and the
standby indicator flashes in
red approx. every 2
seconds.
0
The protection circuit has been activated due to a rise in temperature within this unit. Turn the power off,
wait about an hour until this unit cools down sufficiently, and then turn the power on again.
27
0
Please re-install this unit in a place having good ventilation.
－
Power turns off and the
standby indicator flashes in
red approx. every 0.5
seconds.
0
Check the speaker connections. The protection circuit may have been activated because speaker cable
core wires came in contact with each other or a core wire was disconnected from the connector and
came in contact with the rear panel of this unit. After unplugging the power cord, firmly re-twist the core
wire, and then reconnect the wire.
17
0
Turn down the volume and turn on the power again.
27
0
This unit’s amplifier circuit has failed. Unplug the power cord and contact our customer service center.
－
Contents
Connections
Playback
Settings
Tips
Appendix
57
Front panel
Display
Rear panel
Remote
Index