Kyocera ECOSYS P2235dn Kyocera Command Center RX User Guide Rev-9.2016.6 - Page 107

System stamp, System stamp settings

Get Kyocera ECOSYS P2235dn PDF manuals and user guides View all Kyocera ECOSYS P2235dn manuals
Add to My Manuals
Save this manual to your list of manuals

Page 107 highlights

Management Settings Trap Recipient Click Settings button to finalize the settings. 3. Configure SNMPv3 as follows. After you have changed the setting, you must restart the printing system. SNMPv3 Sets whether to use the SNMPv3 protocol. Select either On or Off in the Protocol Settings page under Network Settings. To configure SNMP v3, proceed as follows. Authentication Sets whether the user authentication is performed in SNMP communication. Hash Select either MD5 or SHA1 for Hash algorithm. This item becomes active when the Authentication is set to On. Privacy Sets whether to encrypt the communicated data in SNMP communication. This becomes available when Authentication is set to On. Encryption Select either DES or AES for encryption algorithm. This item becomes active when the Authentication is set to On. Read Only User Enter User Name and Password of the read-only user. Read/Write User Enter User Name and Password of the read/write user. 4. Click Submit button. System stamp This section includes advanced settings that apply to the system stamp. System stamp settings The system stamps include character and serial numbered stamps. Both are applied to printing, sending, and storing jobs. For example, the following describes how to apply the character and serial numbered stamps to a printing job. Setting a Character Stamp 1. Click System Stamp under Management Settings on the navigation menu. The System Stamp Settings page opens. 2. To apply a character stamp to a print job, proceed as follow. Select On or Off and click Settings button. User Guide 103

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Management Settings
User Guide
103
Trap Recipient
Click
Settings
button to finalize the settings.
3.
Configure
SNMPv3
as follows. After you have changed the setting, you must restart the
printing system.
SNMPv3
Sets whether to use the SNMPv3 protocol. Select either
On
or
Off
in the
Protocol
Settings
page under
Network Settings
. To configure SNMP v3, proceed as fol-
lows.
Authentication
Sets whether the user authentication is performed in SNMP communication.
Hash
Select either
MD5
or
SHA1
for Hash algorithm. This item becomes active when the
Authentication is set to
On
.
Privacy
Sets whether to encrypt the communicated data in SNMP communication. This
becomes available when Authentication is set to
On
.
Encryption
Select either
DES
or
AES
for encryption algorithm. This item becomes active when
the Authentication is set to
On
.
Read Only User
Enter
User Name
and
Password
of the read-only user.
Read/Write User
Enter
User Name
and
Password
of the read/write user.
4.
Click
Submit
button.
System stamp
This section includes advanced settings that apply to the system stamp.
System stamp settings
The system stamps include character and serial numbered stamps. Both are applied to
printing, sending, and storing jobs. For example, the following describes how to apply
the character and serial numbered stamps to a printing job.
Setting a Character Stamp
1.
Click
System Stamp
under
Management Settings
on the navigation menu. The
System Stamp Settings
page opens.
2.
To apply a character stamp to a print job, proceed as follow. Select
On
or
Off
and click
Settings
button.