Invacare CXE Owners Manual - Page 47

Using/Installing/Adjusting Cantilever Arms

Get Invacare CXE PDF manuals and user guides View all Invacare CXE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

SECTION 6-ARMS Locknut Coved Spacer Hex Bolt Rear Arm Socket Nylon Shim Rear Arm Socket Mount Wheelchair Frame FIGURE 6.3 Repositioning Conventional Arms - Repositioning Rear Arm Sockets Repositioning Front Arm Sockets NOTE: For this procedure, refer to FIGURE 6.4. 1. Determine the necessary front arm socket position for the necessary seat depth. Refer to Changing Seat Depth on page 86. 2. Remove locknut and screw that secure the front arm socket to the wheelchair. 3. Move the front arm socket to the position determined in STEP 1. 4. Resecure the front arm socket to the wheelchair with the screw and locknut. 5. Repeat STEPS 1‐4 for the opposite side of the wheelchair. Front Arm Socket Locknut Wheelchair Frame Hex Bolt FIGURE 6.4 Repositioning Conventional Arms - Repositioning Front Arm Sockets Using/Installing/Adjusting Cantilever Arms NOTE: The cantilever arms are designed for use with the fixed height back canes only. Using Locking Cantilever Arms NOTE: For this procedure, refer to FIGURE 6.5 on page 48. 1. Push the locking mechanism actuator towards the front of the wheelchair. 2. While holding the locking mechanism actuator, pull up on the cantilever arm towards the rear of the wheelchair. 3. If necessary, the locking mechanism in the cantilever arm can be repositioned so the cantilever arm will open down instead of up. Refer to Adjusting Cantilever Arm Pad Depth/Replacing Cantilever Arm Pad on page 54. 4. To lock the cantilever arm, push down until there is an audible click. 5. Pull up on the cantilever arm to make sure it is locked in place. Part No 1127114 47 Compass™XE and Allegro®

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
SECTION 6—ARMS
Part No 1127114
47
Compass™XE
and Allegro®
FIGURE 6.3
Repositioning Conventional Arms - Repositioning Rear Arm Sockets
Repositioning Front Arm Sockets
NOTE: For this procedure, refer to FIGURE 6.4.
1.
Determine the necessary front arm
socket position for the necessary seat
depth. Refer to Changing Seat Depth
on page 86.
2.
Remove locknut and screw that secure
the front arm socket to the wheelchair.
3.
Move the front arm socket to the
position determined in STEP 1.
4.
Resecure the front arm socket to the
wheelchair with the screw and locknut.
5.
Repeat STEPS 1
‐
4 for the opposite side
of the wheelchair.
FIGURE 6.4
Repositioning Conventional
Arms - Repositioning Front Arm Sockets
Using/Installing/Adjusting Cantilever Arms
NOTE: The cantilever arms are designed for use with the fixed height back canes only.
Using Locking Cantilever Arms
NOTE: For this procedure, refer to FIGURE 6.5 on page 48.
1.
Push the locking mechanism actuator towards the front of the wheelchair.
2.
While holding the locking mechanism actuator, pull up on the cantilever arm towards
the rear of the wheelchair.
3.
If necessary, the locking mechanism in the cantilever arm can be repositioned so the
cantilever arm will open down instead of up. Refer to Adjusting Cantilever Arm Pad
Depth/Replacing Cantilever Arm Pad
on page 54.
4.
To lock the cantilever arm, push down until there is an audible click.
5.
Pull up on the cantilever arm to make sure it is locked in place.
Locknut
Coved Spacer
Wheelchair Frame
Rear Arm Socket Mount
Nylon Shim
Rear Arm Socket
Hex Bolt
Locknut
Wheelchair
Frame
Hex Bolt
Front Arm
Socket