HP Latex R2000 Site Preparation Guide - Page 7

RIP installation, Networking, Printing supplies for testing and training

Get HP Latex R2000 PDF manuals and user guides View all HP Latex R2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

RIP installation If you have bought HP RIP software for your printer: ● You must ensure that a computer is available on which to install the RIP. ● For full functionality, you are recommended to ensure that the computer is connected to the Internet. ● You must ensure that the HP RIP software has arrived by the agreed date of printer installation. If you have bought non-HP RIP software for your printer: NOTE: This guide does not provide information about your RIP solution. ● You must install the RIP on a suitable computer and ensure that it is fully functional by the agreed date of printer installation. ● For full functionality, you are recommended to ensure that the computer is connected to the Internet. ● You must ensure that a RIP specialist and a network specialist are present on the agreed date of printer installation. Networking You are responsible for all networking requirements, and you must complete the following tasks: NOTE: In order to perform remote support, the printer must have access to the Internet using the LAN connection. ● Have an adequate network ready for the day of installation. See Computer and networking requirements on page 17. ● Provide a CAT-6 LAN cable to connect the printer to your LAN on the day of installation. Printing supplies for testing and training You are responsible for providing the following printing supplies: ● Eight ink cartridges If you intend to install the White Ink Upgrade Kit: The two corresponding cartridges and the optimizer (no cartridges are supplied with the printer) NOTE: In addition, you are recommended to have a second set of ink cartridges, printheads, and one HP Latex Cleaning Roll, in case any replacements are needed. ● If you intend to install the Roll Printing Kit: Compressed air supply for the pneumatic spindle (see Air pressure supply on page 11) ● Substrate for printing-preferably the substrate type that you plan to use most in future ● 10 liters of distilled water ● Self-adhesive vinyl substrate for the printhead alignment process, to be done during installation Return the site preparation checklist The checklist must be completed and returned to your reseller or service representative a minimum of two weeks before the day of installation. NOTE: Any delays during installation that are caused by an unprepared site will be charged to the customer. Take care that your site is properly prepared to ensure a smooth and easy installation. ENWW Customer responsibility 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
RIP installation
If you have bought HP RIP software for your printer:
●
You must ensure that a computer is available on which to install the RIP.
●
For full functionality, you are recommended to ensure that the computer is connected to the Internet.
●
You must ensure that the HP RIP software has arrived by the agreed date of printer installation.
If you have bought non-HP RIP software for your printer:
NOTE:
This guide does not provide information about your RIP solution.
●
You must install the RIP on a suitable computer and ensure that it is fully functional by the agreed date of
printer installation.
●
For full functionality, you are recommended to ensure that the computer is connected to the Internet.
●
You must ensure that a RIP specialist and a network specialist are present on the agreed date of printer
installation.
Networking
You are responsible for all networking requirements, and you must complete the following tasks:
NOTE:
In order to perform remote support, the printer must have access to the Internet using the LAN
connection.
●
Have an adequate network ready for the day of installation. See
Computer and networking requirements
on page
17
.
●
Provide a CAT-6 LAN cable to connect the printer to your LAN on the day of installation.
Printing supplies for testing and training
You are responsible for providing the following printing supplies:
●
Eight ink cartridges
If you intend to install the White Ink Upgrade Kit:
The two corresponding cartridges and the optimizer (no
cartridges are supplied with the printer)
NOTE:
In addition, you are recommended to have a second set of ink cartridges, printheads, and one HP
Latex Cleaning Roll, in case any replacements are needed.
●
If you intend to install the Roll Printing Kit:
Compressed air supply for the pneumatic spindle (see
Air
pressure supply
on page
11
)
●
Substrate for printing—preferably the substrate type that you plan to use most in future
●
10 liters of distilled water
●
Self-adhesive vinyl substrate for the printhead alignment process, to be done during installation
Return the site preparation checklist
The checklist must be completed and returned to your reseller or service representative a minimum of two
weeks before the day of installation.
NOTE:
Any delays during installation that are caused by an unprepared site will be charged to the customer.
Take care that your site is properly prepared to ensure a smooth and easy installation.
ENWW
Customer responsibility
3