Dell XPS 13 9370 XPS 13 Service Manual - Page 27

Replacing the display assembly, Procedure, Post-requisites, Connectors on the wireless card

Get Dell XPS 13 9370 PDF manuals and user guides View all Dell XPS 13 9370 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

16 Replacing the display assembly NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure 1. Slide the palm-rest assembly under the hinges of the display assembly. 2. Using the alignment posts, press the display hinges down on the palm-rest assembly, aligning the screw holes on the display hinges with the screw holes on the palm-rest assembly. 3. Connect the display cable to the system board. 4. Align the screw holes on the display-cable bracket with the screw holes on the system board. 5. Replace the two screws (M1.6x2.5) that secure the display-cable bracket to system board. 6. Connect the antenna cables to the system board. The following table provides the antenna cable color schemes for the wireless card supported by your computer. Table 2. Antenna-cable color scheme Connectors on the wireless card Antenna-cable color Main (white triangle) White Auxiliary (black triangle) Black 7. Connect the camera cable to the system board, adhering the tape securing the camera cable to the fans. 8. Align the screw hole on the wireless antenna and camera cable bracket to screw hole on the system board. 9. Replace the screw (M1.6x3L) that secures the wireless antenna and camera cable bracket to the system board. Post-requisites Replace the base cover. Replacing the display assembly 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
Replacing the display assembly
NOTE:
Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in
Before working inside your computer
. After working inside your computer, follow the instructions in
After
working inside your computer
. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance
.
Procedure
1.
Slide the palm-rest assembly under the hinges of the display assembly.
2.
Using the alignment posts, press the display hinges down on the palm-rest assembly, aligning the screw holes on the display hinges
with the screw holes on the palm-rest assembly.
3.
Connect the display cable to the system board.
4.
Align the screw holes on the display-cable bracket with the screw holes on the system board.
5.
Replace the two screws (M1.6x2.5) that secure the display-cable bracket to system board.
6.
Connect the antenna cables to the system board.
The following table provides the antenna cable color schemes for the wireless card supported by your computer.
Table 2. Antenna-cable color scheme
Connectors on the wireless card
Antenna-cable color
Main (white triangle)
White
Auxiliary (black triangle)
Black
7.
Connect the camera cable to the system board, adhering the tape securing the camera cable to the fans.
8.
Align the screw hole on the wireless antenna and camera cable bracket to screw hole on the system board.
9.
Replace the screw (M1.6x3L) that secures the wireless antenna and camera cable bracket to the system board.
Post-requisites
Replace the
base cover
.
16
Replacing the display assembly
27