Compaq Pro 6305 Maintenance and Service Guide Pro 6305 Microtower Business PC - Page 87

Removing a Hard Drive from a Drive Bay, System Board Connections, on Preparation for Disassembly

Page 87 highlights

8. If installing a new drive, connect the opposite end of the data cable to the appropriate system board connector. NOTE: If you are installing a new SATA optical drive, connect the data cable for the first optical drive to the white SATA connector on the system board labeled SATA2. Connect the data cable for a second optical drive to the black SATA connector on the system board labeled ESATA. If the ESATA connector is already populated, connect the second optical drive to the light blue connector labeled SATA1. Refer to System Board Connections on page 69 for an illustration of the system board drive connectors. 9. Replace the front bezel and computer access panel. 10. Reconnect the power cord and any external devices, then turn on the computer. 11. Lock any security devices that were disengaged when the access panel was removed. Removing a Hard Drive from a Drive Bay NOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive. 1. Prepare the computer for disassembly (Preparation for Disassembly on page 54) 2. Remove the access panel (Computer Access Panel on page 55) 3. Disconnect the power cable and data cable from the back of the hard drive. 4. Release the drive by pulling the release tab away from the drive (1) and sliding the drive out of the bay (2). Figure 6-22 Removing a Hard Drive 5. Remove the four guide screws (two on each side) from the old drive. You will need these screws to install a new drive. Drives 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232

8.
If installing a new drive, connect the opposite end of the data cable to the appropriate system
board connector.
NOTE:
If you are installing a new SATA optical drive, connect the data cable for the first optical
drive to the white SATA connector on the system board labeled SATA2. Connect the data cable
for a second optical drive to the black SATA connector on the system board labeled ESATA. If the
ESATA connector is already populated, connect the second optical drive to the light blue
connector labeled SATA1.
Refer to
System Board Connections
on page
69
for an illustration of the system board drive
connectors.
9.
Replace the front bezel and computer access panel.
10.
Reconnect the power cord and any external devices, then turn on the computer.
11.
Lock any security devices that were disengaged when the access panel was removed.
Removing a Hard Drive from a Drive Bay
NOTE:
Before you remove the old hard drive, be sure to back up the data from the old hard drive so
that you can transfer the data to the new hard drive.
1.
Prepare the computer for disassembly (
Preparation for Disassembly
on page
54
)
2.
Remove the access panel (
Computer Access Panel
on page
55
)
3.
Disconnect the power cable and data cable from the back of the hard drive.
4.
Release the drive by pulling the release tab away from the drive
(1)
and sliding the drive out of
the bay
(2)
.
Figure 6-22
Removing a Hard Drive
5.
Remove the four guide screws (two on each side) from the old drive. You will need these screws to
install a new drive.
Drives
77