Home » Compaq Manuals » Desktops » Compaq Pro 6305 » Manual Viewer

Compaq Pro 6305 Maintenance and Service Guide Pro 6305 Microtower Business PC - Page 81

Extra Guide Screw Locations,

Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

When installing drives, follow these guidelines: ● The primary Serial ATA (SATA) hard drive must be connected to the dark blue primary SATA connector on the system board labeled SATA0. If you are adding a second hard drive, connect it to the light blue connector on the system board labeled SATA1. ● Connect the first SATA optical drive to the white SATA connector on the system board labeled SATA2. If you are adding a second optical drive connect it to the black SATA connector on the system board labeled ESATA. If the ESATA connector is already populated, connect the second optical drive to the light blue connector on the system board labeled SATA1. ● Connect an optional eSATA adapter cable to the black SATA connector on the system board labeled ESATA. ● Connect a media card reader USB cable to the USB connector on the system board labeled MEDIA. ● The power cable for the SATA optical drives is a two-headed cable this is plugged into the system board with the first connector routed to the top 5.25-inch bay and the second connector routed to the bottom 5.25-inch bay. ● The power cable for the SATA hard drives is a two-headed cable this is plugged into the system board with the first connector routed to the bottom 3.5-inch bay and the second connector routed to the top 3.5-inch bay. ● The system does not support Parallel ATA (PATA) optical drives or PATA hard drives. ● You must install guide screws to ensure the drive will line up correctly in the drive cage and lock in place. HP has provided extra guide screws for the drive bays (four 6-32 isolation mounting guide screws and eight M3 metric guide screws), installed on the side of the drive bays. The 6-32 isolation mounting screws are required for a secondary hard drive. All other drives (except the primary hard drive) use M3 metric screws. The HP-supplied metric screws are black and the HPsupplied isolation mounting screws are silver and blue. If you are replacing the primary hard drive, you must remove the four silver and blue 6-32 isolation mounting guide screws from the old hard drive and install them in the new hard drive. Figure 6-13 Extra Guide Screw Locations Drives 71

Section	Page
Product Features	11
Standard Configuration Features	11
Microtower (MT) Front Panel Components	12
Small Form Factor (SFF) Front Panel Components	13
Microtower (MT) Rear Panel Components	14
Small Form Factor (SFF) Rear Panel Components	15
Serial Number Location	16
Activating and Customizing the Software	17
Activating and customizing the software in Windows 7	17
Activating the Windows operating system	17
Downloading Windows 7 updates	18
Installing or upgrading device drivers	18
Customizing the monitor display	18
Activating and customizing the software in Windows 8	18
Activating the Windows Operating System	18
Downloading Windows 8 updates	19
Customizing the monitor display	19
Computer Setup (F10) Utility	20
Computer Setup (F10) Utilities	20
Using Computer Setup (F10) Utilities	21
Computer Setup—File	22
Computer Setup—Storage	23
Computer Setup—Security	26
Computer Setup—Power	31
Computer Setup—Advanced	32
Recovering the Configuration Settings	34
Illustrated parts catalog	35
Microtower (MT) chassis spare parts	35
Computer major components	35
Cables	37
Misc parts	38
Drives	40
Misc boards	40
Sequential part number listing	41
Small Form Factor (SFF) chassis spare parts	45
Computer major components	45
Cables	47
Misc parts	48
Drives	50
Misc boards	50
Sequential part number listing	51
Routine Care, SATA Drive Guidelines, and Disassembly Preparation	55
Electrostatic Discharge Information	55
Generating Static	55
Preventing Electrostatic Damage to Equipment	56
Personal Grounding Methods and Equipment	56
Grounding the Work Area	57
Recommended Materials and Equipment	57
Operating Guidelines	58
Routine Care	58
General Cleaning Safety Precautions	58
Cleaning the Computer Case	59
Cleaning the Keyboard	59
Cleaning the Monitor	59
Cleaning the Mouse	60
Service Considerations	60
Power Supply Fan	60
Tools and Software Requirements	60
Screws	60
Cables and Connectors	61
Hard Drives	61
Lithium Coin Cell Battery	61
SATA Hard Drives	62
SATA Hard Drive Cables	62
SATA Data Cable	62
SMART ATA Drives	62
Cable Management	62
Hard Drive Capacities	63
Removal and Replacement Procedures Microtower (MT) Chassis	64
Preparation for Disassembly	64
Computer Access Panel	65
Front Bezel	66
Front Bezel Security	67
Bezel Blanks	69
Memory	70
DIMMs	70
DDR3-SDRAM DIMMs	70
Populating DIMM Sockets	71
Installing DIMMs	72
Expansion Cards	74
WLAN module	77
System Board Connections	79
Drives	80
Drive Positions	82
Removing a 5.25-inch or 3.5-inch Drive from a Drive Bay	83
Installing a 5.25-inch or 3.5-inch Drive into a Drive Bay	85
Removing a Hard Drive from a Drive Bay	87
Installing a Hard Drive into an Internal Drive Bay	88
Removing and Replacing a Removable 3.5-inch SATA Hard Drive	90
Front Fan Assembly	95
Front I/O Assembly	96
Power Switch/LED Assembly	97
Heat sink	99
Processor	100
Speaker	101
Rear Chassis Fan	103
Power Supply	105
System Board	106
Removal and Replacement Procedures Small Form Factor (SFF) Chassis	109
Preparation for Disassembly	109
Access Panel	110
Front Bezel	111
Front Bezel Security	112
Bezel Blanks	114
Memory	115
DIMMs	115
DDR3-SDRAM DIMMs	115
Populating DIMM Sockets	116
Installing DIMMs	117
Expansion Card	119
WLAN module	123
System Board Connections	125
Drives	126
Drive Positions	127
Installing and Removing Drives	127
Removing a 5.25-inch Drive from a Drive Bay	129
Installing a 5.25-inch Drive into a Drive Bay	129
Removing a 3.5-inch Drive from a Drive Bay	131
Installing a 3.5-inch Drive into a Drive Bay	133
Removing and Replacing the Primary 3.5-inch Internal Hard Drive	135
Removing and Replacing a Removable 3.5-inch SATA Hard Drive	137
Fan duct	142
Front Fan Assembly	143
Hood Sensor	145
Front I/O, Power Switch Assembly	146
Speaker	148
Heat sink	149
Processor	151
Power Supply	152
System Board	153
Using the Small Form Factor Computer in a Tower Orientation	155
Troubleshooting Without Diagnostics	156
Safety and Comfort	156
Before You Call for Technical Support	156
Helpful Hints	157
Solving General Problems	158
Solving Power Problems	162
Solving Hard Drive Problems	164
Solving Media Card Reader Problems	166
Solving Display Problems	168
Solving Audio Problems	173
Solving Printer Problems	175
Solving Keyboard and Mouse Problems	176
Solving Hardware Installation Problems	179
Solving Network Problems	181
Solving Memory Problems	185
Solving Processor Problems	186
Solving CD-ROM and DVD Problems	187
Solving USB Flash Drive Problems	189
Solving Front Panel Component Problems	190
Solving Internet Access Problems	191
Solving Software Problems	192
Contacting Customer Support	194
HP PC Hardware Diagnostics	195
Why run HP PC Hardware Diagnostics – UEFI	195
How to access and run HP PC Hardware Diagnostics - UEFI	195
Downloading HP PC Hardware Diagnostics to a USB device	196
POST Error Messages	197
POST Numeric Codes and Text Messages	197
Interpreting POST Diagnostic Front Panel LEDs and Audible Codes	205
Password Security and Resetting CMOS	209
Resetting the Password Jumper	209
Clearing and Resetting the CMOS	210
Backup and Recovery	213
Restoring and recovering in Windows 7	213
System Restore	213
System Recovery	213
System Recovery when Windows is responding	214
System Recovery when Windows is not responding	215
System recovery using recovery media	215
Creating recovery media	216
Using recovery media	217
Backup and recovery in Windows 8	217
Backing up your information	218
Performing a system recovery	218
Using the Windows recovery tools	219
Using f11 recovery tools	219
Using Windows 8 operating system media (purchased separately)	220
Battery Replacement	221
Power Cord Set Requirements	224
General Requirements	224
Japanese Power Cord Requirements	224
Country-Specific Requirements	225
Specifications	226
MT Specifications	226
SFF Specifications	227

Match case Limit results 1 per page

When installing drives, follow these guidelines:

●

The primary Serial ATA (SATA) hard drive must be connected to the dark blue primary SATA

connector on the system board labeled SATA0. If you are adding a second hard drive, connect it

to the light blue connector on the system board labeled SATA1.

●

Connect the first SATA optical drive to the white SATA connector on the system board labeled

SATA2. If you are adding a second optical drive connect it to the black SATA connector on the

system board labeled ESATA. If the ESATA connector is already populated, connect the second

optical drive to the light blue connector on the system board labeled SATA1.

●

Connect an optional eSATA adapter cable to the black SATA connector on the system board

labeled ESATA.

●

Connect a media card reader USB cable to the USB connector on the system board labeled

MEDIA.

●

The power cable for the SATA optical drives is a two-headed cable this is plugged into the system

board with the first connector routed to the top 5.25-inch bay and the second connector routed to

the bottom 5.25-inch bay.

●

The power cable for the SATA hard drives is a two-headed cable this is plugged into the system

board with the first connector routed to the bottom 3.5-inch bay and the second connector routed

to the top 3.5-inch bay.

●

The system does not support Parallel ATA (PATA) optical drives or PATA hard drives.

●

You must install guide screws to ensure the drive will line up correctly in the drive cage and lock in

place. HP has provided extra guide screws for the drive bays (four 6-32 isolation mounting guide

screws and eight M3 metric guide screws), installed on the side of the drive bays. The 6-32

isolation mounting screws are required for a secondary hard drive. All other drives (except the

primary hard drive) use M3 metric screws. The HP-supplied metric screws are black and the HP-

supplied isolation mounting screws are silver and blue. If you are replacing the primary hard

drive, you must remove the four silver and blue 6-32 isolation mounting guide screws from the old

hard drive and install them in the new hard drive.

Figure 6-13

Extra Guide Screw Locations

Drives