Home » Compaq Manuals » Desktops » Compaq Pro 6305 » Manual Viewer

Compaq Pro 6305 Maintenance and Service Guide Pro 6305 Microtower Business PC - Page 205

Interpreting POST Diagnostic Front Panel LEDs and Audible Codes

Add to My Manuals
Save this manual to your list of manuals

Page 205 highlights

Table 10-1 Numeric Codes and Text Messages (continued) Control panel message Description 2240-ME image unlock failure Special system configurations with reduced ME firmware image require BIOS control of ME firmware upgrading. A failure has occurred prior to the ME firmware update process in which the BIOS could not unlock the ME firmware region. Invalid Electronic Serial Number Electronic serial number is missing. Network Server Mode Active and No Keyboard Attached Keyboard failure while Network Server Mode enabled. Parity Check 2 Parity RAM failure. Recommended action 1. Reboot the computer. 2. If the error persists, update to the latest BIOS version and ME firmware version. 3. If the error still persists, replace the system board. Enter the correct serial number in Computer Setup. 1. Reconnect keyboard with computer turned off. 2. Check connector for bent or missing pins. 3. Ensure that none of the keys are depressed. 4. Replace keyboard. Run Computer Setup and Diagnostic utilities. Interpreting POST Diagnostic Front Panel LEDs and Audible Codes This section covers the front panel LED codes as well as the audible codes that may occur before or during POST that do not necessarily have an error code or text message associated with them. WARNING! When the computer is plugged into an AC power source, voltage is always applied to the system board. To reduce the risk of personal injury from electrical shock and/or hot surfaces, be sure to disconnect the power cord from the wall outlet and allow the internal system components to cool before touching. NOTE: If you see flashing LEDs on a PS/2 keyboard, look for flashing LEDs on the front panel of the computer and refer to the following table to determine the front panel LED codes. Recommended actions in the following table are listed in the order in which they should be performed. Not all diagnostic lights and audible codes are available on all models. Table 10-2 Diagnostic Front Panel LEDs and Audible Codes Activity Beeps Possible Cause Recommended Action Green Power LED On. None Computer on. None Green Power LED flashes every None two seconds. Computer in Suspend to RAM mode (some models only) or normal Suspend mode. None required. Press any key or move the mouse to wake the computer. Interpreting POST Diagnostic Front Panel LEDs and Audible Codes 195

Section	Page
Product Features	11
Standard Configuration Features	11
Microtower (MT) Front Panel Components	12
Small Form Factor (SFF) Front Panel Components	13
Microtower (MT) Rear Panel Components	14
Small Form Factor (SFF) Rear Panel Components	15
Serial Number Location	16
Activating and Customizing the Software	17
Activating and customizing the software in Windows 7	17
Activating the Windows operating system	17
Downloading Windows 7 updates	18
Installing or upgrading device drivers	18
Customizing the monitor display	18
Activating and customizing the software in Windows 8	18
Activating the Windows Operating System	18
Downloading Windows 8 updates	19
Customizing the monitor display	19
Computer Setup (F10) Utility	20
Computer Setup (F10) Utilities	20
Using Computer Setup (F10) Utilities	21
Computer Setup—File	22
Computer Setup—Storage	23
Computer Setup—Security	26
Computer Setup—Power	31
Computer Setup—Advanced	32
Recovering the Configuration Settings	34
Illustrated parts catalog	35
Microtower (MT) chassis spare parts	35
Computer major components	35
Cables	37
Misc parts	38
Drives	40
Misc boards	40
Sequential part number listing	41
Small Form Factor (SFF) chassis spare parts	45
Computer major components	45
Cables	47
Misc parts	48
Drives	50
Misc boards	50
Sequential part number listing	51
Routine Care, SATA Drive Guidelines, and Disassembly Preparation	55
Electrostatic Discharge Information	55
Generating Static	55
Preventing Electrostatic Damage to Equipment	56
Personal Grounding Methods and Equipment	56
Grounding the Work Area	57
Recommended Materials and Equipment	57
Operating Guidelines	58
Routine Care	58
General Cleaning Safety Precautions	58
Cleaning the Computer Case	59
Cleaning the Keyboard	59
Cleaning the Monitor	59
Cleaning the Mouse	60
Service Considerations	60
Power Supply Fan	60
Tools and Software Requirements	60
Screws	60
Cables and Connectors	61
Hard Drives	61
Lithium Coin Cell Battery	61
SATA Hard Drives	62
SATA Hard Drive Cables	62
SATA Data Cable	62
SMART ATA Drives	62
Cable Management	62
Hard Drive Capacities	63
Removal and Replacement Procedures Microtower (MT) Chassis	64
Preparation for Disassembly	64
Computer Access Panel	65
Front Bezel	66
Front Bezel Security	67
Bezel Blanks	69
Memory	70
DIMMs	70
DDR3-SDRAM DIMMs	70
Populating DIMM Sockets	71
Installing DIMMs	72
Expansion Cards	74
WLAN module	77
System Board Connections	79
Drives	80
Drive Positions	82
Removing a 5.25-inch or 3.5-inch Drive from a Drive Bay	83
Installing a 5.25-inch or 3.5-inch Drive into a Drive Bay	85
Removing a Hard Drive from a Drive Bay	87
Installing a Hard Drive into an Internal Drive Bay	88
Removing and Replacing a Removable 3.5-inch SATA Hard Drive	90
Front Fan Assembly	95
Front I/O Assembly	96
Power Switch/LED Assembly	97
Heat sink	99
Processor	100
Speaker	101
Rear Chassis Fan	103
Power Supply	105
System Board	106
Removal and Replacement Procedures Small Form Factor (SFF) Chassis	109
Preparation for Disassembly	109
Access Panel	110
Front Bezel	111
Front Bezel Security	112
Bezel Blanks	114
Memory	115
DIMMs	115
DDR3-SDRAM DIMMs	115
Populating DIMM Sockets	116
Installing DIMMs	117
Expansion Card	119
WLAN module	123
System Board Connections	125
Drives	126
Drive Positions	127
Installing and Removing Drives	127
Removing a 5.25-inch Drive from a Drive Bay	129
Installing a 5.25-inch Drive into a Drive Bay	129
Removing a 3.5-inch Drive from a Drive Bay	131
Installing a 3.5-inch Drive into a Drive Bay	133
Removing and Replacing the Primary 3.5-inch Internal Hard Drive	135
Removing and Replacing a Removable 3.5-inch SATA Hard Drive	137
Fan duct	142
Front Fan Assembly	143
Hood Sensor	145
Front I/O, Power Switch Assembly	146
Speaker	148
Heat sink	149
Processor	151
Power Supply	152
System Board	153
Using the Small Form Factor Computer in a Tower Orientation	155
Troubleshooting Without Diagnostics	156
Safety and Comfort	156
Before You Call for Technical Support	156
Helpful Hints	157
Solving General Problems	158
Solving Power Problems	162
Solving Hard Drive Problems	164
Solving Media Card Reader Problems	166
Solving Display Problems	168
Solving Audio Problems	173
Solving Printer Problems	175
Solving Keyboard and Mouse Problems	176
Solving Hardware Installation Problems	179
Solving Network Problems	181
Solving Memory Problems	185
Solving Processor Problems	186
Solving CD-ROM and DVD Problems	187
Solving USB Flash Drive Problems	189
Solving Front Panel Component Problems	190
Solving Internet Access Problems	191
Solving Software Problems	192
Contacting Customer Support	194
HP PC Hardware Diagnostics	195
Why run HP PC Hardware Diagnostics – UEFI	195
How to access and run HP PC Hardware Diagnostics - UEFI	195
Downloading HP PC Hardware Diagnostics to a USB device	196
POST Error Messages	197
POST Numeric Codes and Text Messages	197
Interpreting POST Diagnostic Front Panel LEDs and Audible Codes	205
Password Security and Resetting CMOS	209
Resetting the Password Jumper	209
Clearing and Resetting the CMOS	210
Backup and Recovery	213
Restoring and recovering in Windows 7	213
System Restore	213
System Recovery	213
System Recovery when Windows is responding	214
System Recovery when Windows is not responding	215
System recovery using recovery media	215
Creating recovery media	216
Using recovery media	217
Backup and recovery in Windows 8	217
Backing up your information	218
Performing a system recovery	218
Using the Windows recovery tools	219
Using f11 recovery tools	219
Using Windows 8 operating system media (purchased separately)	220
Battery Replacement	221
Power Cord Set Requirements	224
General Requirements	224
Japanese Power Cord Requirements	224
Country-Specific Requirements	225
Specifications	226
MT Specifications	226
SFF Specifications	227

Match case Limit results 1 per page

Table 10-1

Numeric Codes and Text Messages (continued)

Control panel message

Description

Recommended action

2240-ME image unlock failure

Special system configurations with reduced

ME firmware image require BIOS control of

ME firmware upgrading. A failure has

occurred prior to the ME firmware update

process in which the BIOS could not unlock

the ME firmware region.

Reboot the computer.

If the error persists, update to the latest

BIOS version and ME firmware version.

If the error still persists, replace the

system board.

Invalid Electronic Serial Number

Electronic serial number is missing.

Enter the correct serial number in Computer

Setup.

Network Server Mode Active and No

Keyboard Attached

Keyboard failure while Network Server

Mode enabled.

Reconnect keyboard with computer

turned off.

Check connector for bent or missing

pins.

Ensure that none of the keys are

depressed.

Replace keyboard.

Parity Check 2

Parity RAM failure.

Run Computer Setup and Diagnostic utilities.

Interpreting POST Diagnostic Front Panel LEDs and

Audible Codes

This section covers the front panel LED codes as well as the audible codes that may occur before or

during POST that do not necessarily have an error code or text message associated with them.

WARNING!

When the computer is plugged into an AC power source, voltage is always applied to

the system board. To reduce the risk of personal injury from electrical shock and/or hot surfaces, be

sure to disconnect the power cord from the wall outlet and allow the internal system components to cool

before touching.

NOTE:

If you see flashing LEDs on a PS/2 keyboard, look for flashing LEDs on the front panel of the

computer and refer to the following table to determine the front panel LED codes.

Recommended actions in the following table are listed in the order in which they should be performed.

Not all diagnostic lights and audible codes are available on all models.

Table 10-2

Diagnostic Front Panel LEDs and Audible Codes

Activity

Beeps

Possible Cause

Recommended Action

Green Power LED On.

None

Computer on.

None

Green Power LED flashes every

two seconds.

None

Computer in Suspend to

RAM mode (some models

only) or normal Suspend

mode.

None required. Press any key or move the mouse

to wake the computer.

Interpreting POST Diagnostic Front Panel LEDs and Audible Codes

195