Cisco C1861-SRST-B/K9 Hardware Installation Guide - Page 59

Initial Configuration Using the Cisco CLI-Manual Configuration

Get Cisco C1861-SRST-B/K9 - 1861 Integrated Services Router PDF manuals and user guides
UPC - 882658171147
View all Cisco C1861-SRST-B/K9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Chapter 5 Power-Up and Initial Configuration Procedures Configuring the Router shutdown no ip address ! interface FastEthernet4 shutdown no ip address ! interface FastEthernet5 shutdown no ip address ! interface FastEthernet6 shutdown no ip address ! interface FastEthernet7 shutdown no ip address ! interface FastEthernet8 shutdown no ip address ! interface FastEthernet9 shutdown no ip address ! interface Vlan1 shutdown no ip address ! end Step 11 Respond to the following prompts. Enter 2 to save the initial configuration: [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit. Enter your selection [2]: 2 Building configuration... Use the enabled mode 'configure' command to modify this configuration. Press RETURN to get started! The user prompt appears. Router> Step 12 Verify the initial configuration. See the "Verifying the Initial Configuration" section on page 5-8 for verification procedures. Initial Configuration Using the Cisco CLI-Manual Configuration This section describes how to display a command-line interface (CLI) prompt for configuration using the CLI, and it directs you to documentation for the CLI configuration. You can use the CLI if you see the following messages at the end of the startup sequence: --- System Configuration Dialog --- OL-6425-03 Cisco 1800 Series Integrated Services Routers (Fixed) Hardware Installation Guide 5-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
5-7
Cisco 1800 Series Integrated Services Routers (Fixed) Hardware Installation Guide
OL-6425-03
Chapter 5
Power-Up and Initial Configuration Procedures
Configuring the Router
shutdown
no ip address
!
interface FastEthernet4
shutdown
no ip address
!
interface FastEthernet5
shutdown
no ip address
!
interface FastEthernet6
shutdown
no ip address
!
interface FastEthernet7
shutdown
no ip address
!
interface FastEthernet8
shutdown
no ip address
!
interface FastEthernet9
shutdown
no ip address
!
interface Vlan1
shutdown
no ip address
!
end
Step 11
Respond to the following prompts. Enter
2
to save the initial configuration:
[0] Go to the IOS command prompt without saving this config.
[1] Return back to the setup without saving this config.
[2] Save this configuration to nvram and exit.
Enter your selection [2]:
2
Building configuration...
Use the enabled mode 'configure' command to modify this configuration.
Press RETURN to get started!
The user prompt appears.
Router>
Step 12
Verify the initial configuration. See the
“Verifying the Initial Configuration” section on page 5-8
for
verification procedures.
Initial Configuration Using the Cisco CLI—Manual Configuration
This section describes how to display a command-line interface (CLI) prompt for configuration using
the CLI, and it directs you to documentation for the CLI configuration. You can use the CLI if you see
the following messages at the end of the startup sequence:
--- System Configuration Dialog ---