2009 Yamaha Motorsports FX Nytro XTX Owners Manual - Page 27

2009 Yamaha Motorsports FX Nytro XTX Manual

Get 2009 Yamaha Motorsports FX Nytro XTX PDF manuals and user guides View all 2009 Yamaha Motorsports FX Nytro XTX manuals

Page 27 highlights

Control functions 3 1 (a) 2 (b) Tightening torque: Locknut: 42 Nm (4.2 m·kgf, 30 ft·lbf) ESU12553 Adjusting the air pressure of the front shock absorbers (FX10RTRS) EWS00730 WARNING 1. Locknut 2. Distance A 3. Spring preload adjusting nut The air pressure of the left and right shock absorbers must be adjusted to the same setting. Uneven settings can cause poor handling and loss of stability. This snowmobile is equipped with FOX shock absorbers as standard equipment. The air pressure of the shock absorbers can be adjusted using the shock absorber pump included with your snowmobile. 1. 2. Loosen the locknut. To increase the spring preload and thereby harden the suspension, turn the adjusting nut in direction (a). To decrease the spring preload and thereby soften the suspension, turn the adjusting nut in direction (b). TIP The spring preload setting is determined by measuring distance A, shown in the illustration. The longer distance A is, the higher the spring preload; the shorter distance A is, the lower the spring preload. Spring preload setting*: Minimum (soft): 141.6 mm (5.57 in) Standard: 141.6 mm (5.57 in) Maximum (hard): 151.6 mm (5.97 in) * Distance A changes 1.5 mm (0.06 in) with each full turn of the adjusting nut. 3. Tighten the locknut to the specified torque. NOTICE: Always tighten the locknut against the adjusting nut, and then tighten the locknut to the specified torque. [ECS00860] 1. Shock absorber pump To adjust the air pressure EWS00621 WARNING Support the snowmobile securely on a suitable stand before adjusting the shock absorbers. Otherwise, the snowmobile could fall and cause injury. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Control functions
21
1.
Loosen the locknut.
2.
To increase the spring preload and there-
by harden the suspension, turn the ad-
justing nut in direction (a). To decrease
the spring preload and thereby soften the
suspension, turn the adjusting nut in di-
rection (b).
TIP
The spring preload setting is determined by
measuring distance A, shown in the illustra-
tion. The longer distance A is, the higher the
spring preload; the shorter distance A is, the
lower the spring preload.
3.
Tighten the locknut to the specified
torque.
NOTICE:
Always tighten the
locknut against the adjusting nut, and
then tighten the locknut to the speci-
fied torque.
[ECS00860]
ESU12553
Adjusting the air pressure of the front
shock absorbers (FX10RTRS)
WARNING
EWS00730
The air pressure of the left and right shock
absorbers must be adjusted to the same
setting. Uneven settings can cause poor
handling and loss of stability.
This snowmobile is equipped with FOX shock
absorbers as standard equipment.
The air pressure of the shock absorbers can
be adjusted using the shock absorber pump
included with your snowmobile.
To adjust the air pressure
WARNING
EWS00621
Support the snowmobile securely on a
suitable stand before adjusting the shock
absorbers. Otherwise, the snowmobile
could fall and cause injury.
1. Locknut
2.
Distance A
3.
Spring preload adjusting nut
Spring preload setting*:
Minimum (soft):
141.6 mm (5.57 in)
Standard:
141.6 mm (5.57 in)
Maximum (hard):
151.6 mm (5.97 in)
* Distance A changes 1.5 mm (0.06 in)
with each full turn of the adjusting nut.
(a)
(b)
1
3
2
Tightening torque:
Locknut:
42 Nm (4.2 m·kgf, 30 ft·lbf)
1.
Shock absorber pump