2008 Polaris Kingpin Tour Owners Manual - Page 107

2008 Polaris Kingpin Tour Manual

Page 107 highlights

MAINTENANCE Rear Suspension Adjust Rear Shock Absorber Preload (Ride Height) To adjust the shock absorber spring pre-load: 1. Rest the motorcycle on the sidestand. Remove the right side cover (page 48). 2. Remove the fuse box from right panel by lifting upward on the tab at the rearward end while pulling the fuse box rearward (page 137). Make sure that the rear brake fluid reservoir cap is secured to prevent fluid loss (page 122). 3. Remove three 10mm bolts (1) holding the fuse box bracket to chassis. 4. Remove the on-board diagnostics connector from the fuse box bracket by squeezing the connector lock and pulling the connector apart. Leave the terminated end attached to the fuse box bracket. 5. Remove the wire harness dart from the fuse box bracket by sliding the connector off the dart clip. 6. Carefully pull and rotate the fuse box bracket toward the front of the motorcycle. 1 102

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178

102
MAINTENANCE
Rear Suspension
Adjust Rear Shock Absorber Preload (Ride Height)
To adjust the shock absorber spring pre-load:
1.
Rest the motorcycle on the sidestand. Remove the right side
cover (page 48).
2.
Remove the fuse box from right panel by lifting upward on
the tab at the rearward end while pulling the fuse box
rearward (page 137). Make sure that the rear brake fluid
reservoir cap is secured to prevent fluid loss (page 122).
3.
Remove three 10mm bolts (1) holding the fuse box bracket
to chassis.
4.
Remove the on-board diagnostics connector from the fuse
box bracket by squeezing the connector lock and pulling the
connector apart. Leave the terminated end attached to the
fuse box bracket.
5.
Remove the wire harness dart from the fuse box bracket by
sliding the connector off the dart clip.
6.
Carefully pull and rotate the fuse box bracket toward the front of the motorcycle.
1