2008 Polaris Hammer Owners Manual - Page 97

2008 Polaris Hammer Manual

Get 2008 Polaris Hammer PDF manuals and user guides View all 2008 Polaris Hammer manuals

Page 97 highlights

MAINTENANCE Rear Wheel Alignment NOTE: Turn the axle adjusters about 1/16 of a turn at a time and monitor wheel alignment as you proceed. 5. On screw style adjusters: Use a 17mm wrench to loosen lock nut (4), then an 8mm hexagonal wrench to turn the axle adjuster screws (5). On nut style adjusters: Use a deep 14mm socket to turn the adjuster nut (6). 6. On both styles: Turn the screw or nut IN (clockwise) to draw the axle back, or OUT (counterclockwise) to allow the axle to move forward. NOTE: If adjuster screws or nuts are turned OUT (counterclockwise) push the wheel and axle forward to be sure the end of adjuster screws or the nuts are seated against the end of the swingarm before inspecting alignment or belt tension. 7. Recheck rear wheel alignment after each adjustment. Readjust if necessary until alignment is correct and drive belt tension is correct (see Check Drive Belt Tension, page 86). 8. When wheel is aligned and drive belt tension is correct, tighten the adjuster lock nut (screw-style), then tighten the axle nut. Torque: 65 ft-lbs (88 Nm) 92 4 5 Screw-style adjuster 6 Nut-style adjuster

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
92
MAINTENANCE
Rear Wheel
Alignment
NOTE:
Turn the axle adjusters about 1/16 ofa turn at atime and monitor
wheel alignment as you proceed.
5.
On screw style adjusters
: Use a 17mm wrench to loosen lock
nut (4), then an 8mm hexagonal wrench to turn the axle adjuster
screws (5).
On nut style adjusters
: Use a deep 14mm socket to turn the
adjuster nut (6).
6.
On both styles:
Turn the screw or nut IN (clockwise) to draw the
axle back, or OUT (counterclockwise) to allow the axle to move
forward.
NOTE:
If adjuster screws or nuts are turned OUT (counterclockwise)
push the wheel and axle forward to be sure the end of adjuster screws
or the nuts are seated against the end of the swingarm before inspect-
ing alignment or belt tension.
7.
Recheck rear wheel alignment after each adjustment. Readjust
if necessary until alignment is correct and drive belt tension is
correct (see Check Drive Belt Tension, page 86).
8.
When wheel is aligned and drive belt tension is correct, tighten
the adjuster lock nut (screw-style), then tighten the axle nut.
Torque: 65 ft-lbs (88 Nm)
5
4
6
Screw-style adjuster
Nut-style adjuster