2005 Polaris Ranger 6x6 Owners Manual - Page 66

2005 Polaris Ranger 6x6 Manual

Get 2005 Polaris Ranger 6x6 PDF manuals and user guides View all 2005 Polaris Ranger 6x6 manuals

Page 66 highlights

MAINTENANCE AND LUBRICATION Engine Oil Oil Check (RANGER TM) 1. Position the vehicle on a level surface. 2. Start the engine and let it idle for 20-30 seconds. 3. Stop the engine and remove the seat as described on page 29. Remove the service panel (1) by pulling upward. 4. Remove the dipstick (2) and wipe it dry with a clean cloth. 5. Replace the dipstick and seat it completely. 6. Remove the dipstick and check to see that the oil level is between the FULL (3) and ADD (4) marks. Add oil through the oil filler hole (5) as needed. Do not overfill. NOTE: 1 5 2 A rising oil level between checks in cool weather driving can indicate moisture collecting in the oil reservoir. If the oil level is over the full mark, change the oil. 6 3 Oil and Filter Change (RANGER TM) 1. Position the vehicle on a level surface. 4 2. Run the engine two to three minutes until warm, then stop the engine. 3. Clean the area around the drain plug (6) at the bottom of the engine. The plug is accessible through the access hole in the bottom of the skid plate. CAUTION Hot oil can cause serious burns. Do not allow hot oil to come into contact with skin. 4. Place a drain pan beneath the engine and remove the drain plug. Allow the oil to drain completely. 64

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
64
MAINTENANCE AND LUBRICATION
Engine Oil
Oil Check (
RANGER
TM)
1.
Position the vehicle on a level
surface.
2.
Start the engine and let it idle for
20-30 seconds.
3.
Stop the engine and remove the
seat as described on page 29.
Remove the service panel (1) by
pulling upward.
4.
Remove the dipstick (2) and wipe
it dry with a clean cloth.
5.
Replace the dipstick and seat it
completely.
6.
Remove the dipstick and check to see
that the oil level is between the FULL
(3) and ADD (4) marks. Add oil
through the oil filler hole (5) as needed.
Do not overfill.
NOTE:
A rising oil level between checks
in cool weather driving can indicate
moisture collecting in the oil reservoir.
If the oil level is over the full mark,
change the oil.
Oil and Filter Change (
RANGER
TM)
1.
Position the vehicle on a level surface.
2.
Run the engine two to three minutes until
warm, then stop the engine.
3.
Clean the area around the drain plug (6) at the bottom of the
engine. The plug is accessible through the access hole in the
bottom of the skid plate.
CAUTION
Hot oil can cause serious burns. Do not allow hot oil to come into
contact with skin.
4.
Place a drain pan beneath the engine and remove the drain plug.
Allow the oil to drain completely.
1
2
4
5
6
3