Viper 3303 Owner Manual - Page 28

Prepare the system, Press, press, Release, Prepare the remote control

Get Viper 3303 PDF manuals and user guides View all Viper 3303 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Prepare the system 1. Open a door. 2. Turn the ignition on. 3. Press and release then press and hold the control center button. The control center LED flashes and the siren chirps one time to confirm the system is prepared. 4. Release the control center button and proceed below. Note: Begin pairing within 60 seconds or the system will exit (indicated by a long siren chirp) and will need to be prepared again. Prepare the remote control Select the desired Car 1 (Default) or Car 2 operation before proceeding. 1. Press and hold the button of the remote control until a long beep is emitted and MAIN MENU is displayed (If programmed to operate two systems, confirm the correct car 1 or car 2 text and beeps at 3 seconds). 2. Release the button to view the main menu. REMOTE SETUP is displayed. 3. Press and release the button two times. PAIR REMOTE is displayed. 4. Press and hold the button until PAIR is displayed, and then release it. 5. Press and hold the button until the siren emits a long chirp. SUCCESS is displayed with a sequence of chimes. Note: If FAILED is displayed, make sure the system is still pre- pared and repeat step 5 until successful. © 2009 Directed Electronics. All rights reserved. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
25
© 2009 Directed Electronics. All rights reserved.
Prepare the system
Open
1.
a door
.
Turn
2.
the ignition on.
Press
3.
and release then
press
and
hold
the control center button.
The control center LED flashes and the siren chirps one time to
confirm the system is prepared.
Release
4.
the control center button and proceed below.
Note:
Begin pairing within 60 seconds or the system will exit (indi-
cated by a long siren chirp) and will need to be prepared again.
Prepare the remote control
Select the desired Car 1 (Default) or Car 2 operation before proceed-
ing.
Press
1.
and
hold
the
button of the remote control until a long
beep is emitted and
MAIN MENU
is displayed (If programmed to
operate two systems, confirm the correct car 1 or car 2 text and
beeps at 3 seconds).
Release the
2.
button to view the main menu.
REMOTE SETUP
is
displayed.
Press
3.
and release the
button two times.
PAIR REMOTE
is
displayed.
Press
4.
and
hold
the
button until
PAIR
is displayed, and then
release it.
Press
5.
and
hold
the
button until the siren emits a long chirp.
SUCCESS
is displayed with a sequence of chimes.
Note:
If
FAILED
is displayed, make sure the system is still pre-
pared and repeat step 5 until successful.