Sabrent SP-TOUR User Manual - Page 4

OPERATION

USER

MANUAL

SP

-TOUR

1.

To

turn

on

the

speaker,

press

and

hold

the

POWER

button

for

3

seconds.

The

GREEN

power

LED

illuminates.

2.

To

turn

off

the

speaker,

press

and

hold

the

POWER

button

for

3

seconds

again.

POWER

ON/OFF

MOOD

LIGHT/PAIR

VOLUME

UP/DOWN

REMOTE

CONTROL

STORAGE

REMOTE

CONTROL

1.

The

remote

control

is

ready

to

use

with

a

factory

-installed

button

cell

battery.

It

can

be

stored

in

the

recessed

area

on

the

front

panel.

2.

Press

"+"

"-"

button

to

get

desired

volume

level.

3.

Press

the

Light

button

to

turn

on/off

the

Mood

light

feature.

4.

When

the

speakers

are

on,

pressing

the

S"

button

puts

them

in

standby

mode.

The

speaker

BLUE

light

changes

to

GREEN.

5.

Pressing

the

®

"

button

while

the

speakers

are

in

standby

mode

puts

them

back

to

active

mode.

The

GREEN

light

changes

to

BLUE.

NOTE:

The

remote

control

can

be

used

to

raise

or

lower

the

volume

or

change

the

status

of

the

speakers

from

active

to

standby

or

from

standby

to

active.

If

the

speakers

are

completely

powered

off

the

remote

will

not

power

the

system

up.

BASIC

OPERATION

1.

When

the

transmitter

is

plugged

in

or

batteries

are

inserted,

turn

the

on/off

switch

to

ON.

The

transmitter's

light

will

be

GREEN.

2.

To

turn

on

the

speaker,

press

and

hold

the

POWER

button

on

the

front

panel

of

the

speaker

for

3

seconds.

The

Power

buttons

light

will

be

GREEN.

3.

Turn

on

the

audio

source

and

set

the

source

volume

to

75%

of

maximum.

The

BLUE

light

on

the

transmitter

and

speaker

illuminate

when

the

audio

signal

link

between

the

two

is

made.

This

will

typically

take

no

more

than

5

seconds.

4.

If

the

audio

source

connected

to

the

transmitter

is

turned

off

for

less

than

4

minutes,

the

BLUE

lights

on

the

transmitter

and

the

speaker

remain

on,

but

no

sound

is

transmitted.

When

the

audio

signal

is

turned

back

on,

sound

is

transmitted

again.

5.

If

no

signal

is

detected

for

more

than

4

minutes,

the

transmitter

automatically

turns

off

and

goes

into

STANDBY

mode.

The

BLUE

lights

on

the

transmitter

and

the

speaker

switch

to

GREEN.

6.

If

no

audio

signal

is

detected

from

the

transmitter

for

more

than

15

minutes,

the

speaker

automatically

turns

off.

The

GREEN

LED

goes

off.

7.

To

turn

speakers

on,

press

the

POWER

button

on

the

front

panel

of

the

speaker

for

3

seconds.

8.

To

turn

the

speakers

off,

press

the

POWER

button

on

the

front

panel

for

3

seconds.

3

Sabrent SP-TOUR User Manual - Page 4

Light/pair

Page 4 highlights