NordicTrack C 990 Instruction Manual - Page 12

If You Do Not Connect

Get NordicTrack C 990 PDF manuals and user guides View all NordicTrack C 990 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

11. IMPORTANT: To avoid damaging the Pulse Crossbar (93), do not use power tools and do 11 not overtighten the #10 x 3/4" Screws (9). Orient the Pulse Crossbar (93) as shown. Attach the Pulse Crossbar to the Handrails (86) with two 28 #10 x 3/4" Screws (9) and two #10 Star Washers (5); start both Screws, and then tighten them. Make sure not to pinch the Upright Wire (81). Firmly tighten the four 5/16" x 2 1/2" Screws (28). 9 5 86 93 9 5 86 28 81 12. With the help of a second person, hold the console assembly (J) near the Handrails (86) (only one side is shown). Connect the ground wire (K) from the console assembly (J) to the Console Ground Wire (58) on the Pulse Crossbar (93). Next, insert the Upright Wire (81) through the two indicated looped ties (L) on the console assembly (J). See the inset drawing. Connect the Upright Wire (81) to the console wire (M). The connectors should slide together easily and snap into place. If they do not, turn one connector and try again. IF YOU DO NOT CONNECT THE CONNECTORS PROPERLY, THE CONSOLE MAY BECOME DAMAGED WHEN YOU TURN ON THE POWER. Then, remove the wire tie (A) from the Upright Wire. 12 L J M 81 86 93 A K 58 M 81 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
12
11.
IMPORTANT: To avoid damaging the Pulse
Crossbar (93), do not use power tools and do
not overtighten the #10 x 3/4" Screws (9).
Orient the Pulse Crossbar (93) as shown. Attach
the Pulse Crossbar to the Handrails (86) with two
#10 x 3/4" Screws (9) and two #10 Star Washers
(5);
start both Screws, and then tighten them.
Make sure not to pinch the Upright Wire (81).
Firmly tighten the four 5/16" x 2 1/2" Screws
(28).
11
9
9
5
5
28
28
86
93
86
81
12
J
L
M
M
A
81
81
86
93
12.
With the help of a second person, hold the con-
sole assembly (J) near the Handrails (86) (only
one side is shown).
Connect the ground wire (K) from the console
assembly (J) to the Console Ground Wire (58)
on the Pulse Crossbar (93).
Next, insert the Upright Wire (81) through the
two indicated looped ties (L) on the console
assembly (J).
See the inset drawing.
Connect the Upright
Wire (81) to the console wire (M).
The connec-
tors should slide together easily and snap
into place.
If they do not, turn one connector
and try again.
IF YOU DO NOT CONNECT THE
CONNECTORS PROPERLY, THE CONSOLE
MAY BECOME DAMAGED WHEN YOU TURN
ON THE POWER.
Then, remove the wire tie (A)
from the Upright Wire.
K
58