LiftMaster 889LM Instructions - English French Spanish Manufactured Prior to 2 - Page 1
LiftMaster 889LM Manual
View all LiftMaster 889LM manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
MyQ® CONTROL PANEL MODEL 889LM APPLICATION The MyQ Control Panel is intended to be installed with Security+® Garage Door Openers manufactured between 1998 and present. The MyQ Control Panel is NOT compatible with Security+ 2.0® Garage Door Openers. DO NOT install this door control on garage door opener systems controlling one-piece or swing doors. OVERVIEW The MyQ Control Panel offers a quick and convenient way to add Security+ 2.0 and MyQ technology to your existing garage door opener. MyQ technology uses a 900MHz signal to provide two-way communication between the garage door opener and MyQ enabled accessories. When programmed to the LiftMaster® Internet Gateway you can monitor and control your garage door from any internet enabled computer or smartphone. You may program up to 12 Security+ 2.0 remote controls, 2 Security+ 2.0 keyless entries and a combination of 16 MyQ accessories to the MyQ control panel. COMPATIBLE ACCESSORIES Security+ 2.0® Accessories: Model 891LM 1- Button Remote Control MyQ Accessories: Model 823LM Remote Light Switch Model 893LM 3-Button Remote Control Model 825LM Remote Light Control Model 890MAX 3-Button Mini MAX Remote Control Model 828LM LiftMaster® Internet Gateway Model 893MAX 3-Button MAX Remote Control Model 829LM Garage Door and Gate Monitor Model 895MAX 3-Button Premium MAX Remote Control Model 877LM Wireless Keyless Entry Model 877MAX Wireless MAX Keyless Entry INSTALLATION Install the MyQ Control Panel in place of the existing door control, within sight of garage door, out of reach of small children at a minimum height of 5 feet (1.5 m) above floors, landings, steps or any other adjacent walking surface, and away from ALL moving parts of door. Due to power consumption the MyQ Control Panel cannot be used in conjunction with another wired door control connected to your garage door opener. If an additional door control is needed, the wireless door control model 885LM can be programmed to the MyQ Control Panel. To program the 885LM to the MyQ Control Panel, follow the remote control programming steps. When in battery back-up mode, any feature using unattended operation such as Timer-to-Close, closure from a garage door and gate monitor or remote operation utilizing the LiftMaster® Internet Gateway will be disabled. 1. Disconnect all electrical and battery power (if applicable) to the garage door opener. 2. Remove the existing door control from the wall. 3. Note the polarity of the wires connected to the existing door control. • Label the wire connected to the RED terminal. • Label the wire connected to the WHITE terminal. Disconnect the wires from the existing door control. 4. Connect the wires to the new MyQ Control Panel. Make sure the polarity is correct. • Red wire to the R terminal. • White wire to the W terminal. To prevent possible SERIOUS INJURY or DEATH from electrocution: • Be sure power is NOT connected BEFORE installing door control. • Connect ONLY to 7-28 VOLT low voltage wires. To prevent possible SERIOUS INJURY or DEATH from a closing garage door: • Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet (1.5 m) above floors, landings, steps or any other adjacent walking surface, and away from ALL moving parts of door. • NEVER permit children to operate or play with door control push buttons or remote control transmitters. • Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. • ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door. • DO NOT install this door control on garage door opener systems controlling one-piece or swing doors. To provide an adequate visual alert, the garage door opener light bulb(s) MUST be a minimum of 40 Watt (or equivalent). WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov. 5. Mount the MyQ Control Panel to the wall. 6. Reconnect power. The yellow command LED and the red learn LED will blink quickly for up to 5 minutes as the control panel recharges. When the control panel is operational, the yellow command LED will glow steadily. 7. To test the control panel, press the push bar to activate the garage door opener. Existing Door Control MyQ Control Panel Wire from WHITE terminal Connect WHITE wire to W terminal Wire from RED terminal Discard, donate or recycle Connect RED wire to R terminal 1