Home » Invacare Manuals » Wheelchairs » Invacare IFX-20R » Manual Viewer

Invacare IFX-20R Owners Manual 1 - Page 106

Using the USB charger

Add to My Manuals
Save this manual to your list of manuals

Page 106 highlights

LiNX® Control System Over voltage This is displayed if the batteries are overcharged. Disconnect the battery charger immediately. Low voltage This is displayed if the batteries are empty. Power down the wheelchair and charge the batteries immediately. Deep discharge This is displayed if the battery voltage falls below the voltage set by Cut Off Voltage. This indicates that the battery is empty and battery damage occurs if the battery is discharged any further. The horn also sounds once every ten seconds for the duration of active deep discharge status. Power down the wheelchair and charge the batteries immediately. 6.20 Using the USB charger WARNING! Risk of injury If you use mobile phone while operating mobility device, accidents could lead to injury or property damage. - Only use mobile phone in conjunction with hands-free equipment to operate mobility device while driving. Risk of property damage Handle USB charger with care, otherwise damage could occur. - Always keep the USB charger dry. If USB charger gets wet, let USB charger dry before use. - Do not use or store USB charger in dusty or dirty areas. - Do not insert sharp objects into the USB ports. WARNING! Risk of Injury or Damage Erratic or unintended movement of the wheelchair may occur if wireless transmitters are connected to the wheelchair. To avoid injury or damage: - DO NOT use the USB charger connector as a wireless transmitter. - Only use the USB charger for the purposes described in this manual. With the USB charger you can charge the battery of your mobile phone or a compatible device when you do not have access to a regular power source. Both USB ports can be used at the same time and each USB port has a charging current up to 1 A. 106 60126082-A

Section	Page
60126082~A~00 artwork 00.pdf	4
1 General	5
1.1 About this manual	5
1.2 Symbols	5
1.3 Prescription Statement	5
1.4 Intended Use	5
1.4.1 Intended Use — REM500	6
1.5 Indication for Use	6
1.6 Service Life	6
2 Safety	7
2.1 General Guidelines	7
2.1.1 Live Edit Guidelines	10
2.1.2 Usage Guidelines	11
2.1.3 Setup and Service Guidelines	12
3 Electromagnetic Compatibility (EMC) Information	14
3.1 Electromagnetic Compatibility	14
3.1.1 Minimizing Emissions	14
4 Components	15
4.1 User interface REM500	15
4.2 Screen composition overview	15
4.2.1 Battery bar	15
4.2.2 Status bar	16
4.2.3 User function screen overview	17
4.3 Navigation button	20
4.4 Labels on the Product	21
5 Setup	24
5.1 Connecting the remote	24
6 Usage	25
6.1 Operating the remote	25
6.1.1 Controls on Menu Screen	26
6.1.2 Settings on Menu Screen	26
6.1.3 Configuring Menu Screen	29
6.1.4 Locking Screen to Avoid Unintentional Response	30
6.2 Navigating through user function screens	31
6.2.1 Function Change Inhibits	31
6.2.2 Using direct navigation	32
6.2.3 Using indirect navigation	34
6.2.4 Menu select	35
6.2.5 Overview scan select	38
6.2.6 Scan select	38
6.3 Using the multipurpose buttons	41
6.4 Proportional driving mode	41
6.4.1 Using the joystick (proportional driving mode)	41
6.4.2 Controlling the maximum speed	42
6.5 Latched driving mode	44
6.5.1 External stop switch	45
6.5.2 1 Step Up	46
6.5.3 3 Step Up	47
6.5.4 5 Step Up	47
6.5.5 3 Step Up/Down	48
6.5.6 5 Step Up/Down	49
6.5.7 Cruise Control	50
6.6 Emergency stop	50
6.7 Operating the position lights	51
6.8 Operating the hazard lights	52
6.9 Operating the turn signals	54
6.10 Operating the horn	55
6.11 Operating Lighting Functions and Horn via Utility Function Card	55
6.12 Locking/unlocking the remote	56
6.13 The sleep mode	57
6.14 Operating powered seating functions	57
6.14.1 Through seating screens	57
6.14.2 Through external switches	60
6.14.3 Speed reduction and seating function inhibits	65
6.15 Connectivity screens	66
6.15.1 Configuring Connectivity Card	66
6.15.2 Mouse Mover	74
NO TITLE	74
Setting up a Mouse Mover	75
Operating the Mouse Mover	78
6.16 Switch Control	79
6.16.1	79
6.16.2 Setting up switch control	80
Configuring Switch Control (Android)	80
Configuring Switch Control (iOS)	83
6.16.3 Operating Switch Control	84
6.17 Using secondary inputs	85
6.17.1 Using the ASL 128 Molecule Joystick (Chin control)	86
6.17.2 Using the ASL 128 Molecule Joystick (Chin Control)	87
6.17.3 Using the Compact Single Switch Joystick	88
6.17.4 Using the Micro Extremity Control joystick	89
6.17.5 Using the Pediatric Compact Joystick	91
6.17.6 Using the Sip and Puff	92
6.17.7 Using the Sip and Puff Head Array	94
6.17.8 Using the Head Array	97
6.17.9 Using the Four Switch Proximity Array	100
6.17.10 Using the Wireless Mouse Emulator	101
6.18 Disabling Bluetooth	104
6.19 Charging the batteries	104
6.19.1 Battery alarms	105
6.20 Using the USB charger	106
7 Maintenance	108
7.1 Maintenance Information	108
7.2 Setup/Delivery Inspection	108
7.3 Wear and Tear Information	108
7.4 User/Attendant Inspection Checklists	109
7.4.1 Inspect/Adjust Weekly	109
7.4.2 Inspect/Adjust Monthly	109
7.4.3 Inspect/Adjust Periodically	109
7.5 Service Inspection	109
7.5.1 Six Month Inspection	110
7.6 Cleaning	110
7.6.1 Cleaning Sip-N-Puff	111
7.7 Replacing Mouthpiece	112
7.8 Replacing Saliva Trap	112
8 Troubleshooting	114
8.1 Fault diagnosis	114
8.1.1 Fault codes and diagnosis codes	114
8.2 OON (“Out Of Neutral”)	115
8.3 Drive inhibit indication	116
9 Technical Data	117
9.1 Technical specifications	117
10 Wireless Technology	118
10.1 Wireless Technology Overview	118
10.2 Intended Wireless (Electromagnetic) Environment	118
10.3 LiNX Wireless Functions	119
10.3.1 Mouse Mover	119
10.3.2 Remote Diagnostics	119
10.3.3 Configuration	119
10.4 Quality of Service	120
10.4.1 Data Integrity	120
10.4.2 Safeguards and Redundancy	120
10.5 Wireless Coexistence	121
10.6 Cybersecurity	121
10.6.1 Cybersecurity Controls	121
10.6.2 User Actions	122
11 Warranty	123
11.1 Limited Warranty—US	123
11.2 Limited Warranty—Canada	123
11.3 Repair or Replacement	123
11.4 Limitations and Exclusions	124