Image Fitness 10.6 Treadmill English Manual - Page 20

Trouble, Shooting, Storage

Page 20 highlights

TROUBLE-SHOOTING AND STORAGE Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call our toll-free HELPLINE at 1-800736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays). 1. SYMPTOM: THE POWER DOES NOT TURN ON a. Make sure that the power cord is plugged into a surge protector, and that the surge protector is plugged into a properly grounded outlet. (See HOW TO PLUG IN THE POWER CORD on page 9.) Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in length. b. After the power cord has been plugged in, make sure that the key is fully inserted into the console. Various indicators on the console should light. (See HOW TO TURN ON THE POWER on page 10.) c. Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in. Tripped Reset d. Check the on/off switch located at the front of the treadmill near the power cord. The switch must be in the "on" position. "On" Position 2. SYMPTOM: THE POWER TURNS OFF DURING USE a. Check the circuit breaker located on the treadmill near the power cord. If the circuit breaker has tripped (see the drawing above), wait for five minutes and then press the switch back in. b. Make sure that the power cord is plugged in. c. Remove the key from the console. Reinsert the key fully into the console. Various indicators on the console should light. d. Check to make sure the on/off switch is in the "on" position. (See 1. d. above.) e. If the treadmill still will not run, please call our toll-free HELPLINE. 3. SYMPTOM: AN ERROR CODE ("El," "E2," "E3," "E4," OR "E5") APPEARS ON THE CONSOLE a. If error code "El" appears in the INCLINE display, a malfunction may have occurred in the incline system. Remove the key, wait for ten seconds, and then reinsert the key. If the error code appears again, call our tollfree HELPLINE. Do not operate the treadmill until the problem is corrected. b. Error code "E2" may appear in the SPEED display if the INCREASE SPEED or PROGRAM START button is pressed and no movement of the walking belt is detected within seven seconds. Remove the key, wait for ten seconds, and then reinsert the key. Make sure that you stand on the side rails of the treadmill each time you start walking belt. If the error code appears again, call our toll-free HELPLINE. Do not operate the treadmill until the problem is corrected. c. Error code "E3" may appear in the SPEED display if the speed of the walking belt surges above the selected speed setting. Remove the key, wait for ten seconds, and then reinsert the key. If the error code appears again, call our toll-free HELPLINE. Do not operate the treadmill until the problem is corrected. d. Error code "E4" may appear in the SPEED display if the walking belt is moving at a slow speed, and there is excessive stress on the motor. Remove the key, wait for ten seconds, and then reinsert the key. If you weigh over 200 pounds, it may be helpful to increase the incline of the treadmill. If the error code appears again, call 20 our toll-free HELPLINE. Do not operate the treadmill until the problem is corrected.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27

TROUBLE
-SHOOTING
AND
STORAGE
Most
treadmill
problems
can
be
solved
by
following
the
simple
steps
below.
Find
the
symptom
that
applies,
and
follow
the
steps
listed.
If
further
assistance
is
needed,
call
our
toll
-free
HELPLINE
at
1-800-
736-6879,
Monday
through
Saturday,
7
a.m.
until
7
p.m.
Central
Time
(excluding
holidays).
1.
SYMPTOM:
THE
POWER
DOES
NOT
TURN
ON
a.
Make
sure
that
the
power
cord
is
plugged
into
a
surge
protector,
and
that
the
surge
protector
is
plugged
into
a
properly
grounded
outlet.
(See
HOW
TO
PLUG
IN
THE
POWER
CORD
on
page
9.)
Use
only
a
UL
-listed
surge
protector,
rated
at
15
amps,
with
a
14
-gauge
cord
of
five
feet
or
less
in
length.
b.
After
the
power
cord
has
been
plugged
in,
make
sure
that
the
key
is
fully
inserted
into
the
console.
Various
indicators
on
the
console
should
light.
(See
HOW
TO
TURN
ON
THE
POWER
on
page
10.)
20
c.
Check
the
circuit
breaker
located
on
the
treadmill
near
the
power
cord.
If
the
switch
protrudes
as
shown,
the
circuit
break-
er
has
tripped.
To
reset
the
circuit
breaker,
wait
for
five
min-
utes
and
then
press
the
switch
back
in.
d.
Check
the
on/off
switch
located
at
the
front
of
the
treadmill
near
the
power
cord.
The
switch
must
be
in
the
"on"
position.
Tripped
Reset
"On"
Position
2.
SYMPTOM:
THE
POWER
TURNS
OFF
DURING
USE
a.
Check
the
circuit
breaker
located
on
the
treadmill
near
the
power
cord.
If
the
circuit
breaker
has
tripped
(see
the
drawing
above),
wait
for
five
minutes
and
then
press
the
switch
back
in.
b.
Make
sure
that
the
power
cord
is
plugged
in.
c.
Remove
the
key
from
the
console.
Reinsert
the
key
fully
into
the
console.
Various
indicators
on
the
console
should
light.
d.
Check
to
make
sure
the
on/off
switch
is
in
the
"on"
position.
(See
1.
d.
above.)
e.
If
the
treadmill
still
will
not
run,
please
call
our
toll
-free
HELPLINE.
3.
SYMPTOM:
AN
ERROR
CODE
("El,"
"E2,"
"E3,"
"E4,"
OR
"E5")
APPEARS
ON
THE
CONSOLE
a.
If
error
code
"El"
appears
in
the
INCLINE
display,
a
malfunction
may
have
occurred
in
the
incline
system.
Remove
the
key,
wait
for
ten
seconds,
and
then
reinsert
the
key.
If
the
error
code
appears
again,
call
our
toll
-
free
HELPLINE.
Do
not
operate
the
treadmill
until
the
problem
is
corrected.
b.
Error
code
"E2"
may
appear
in
the
SPEED
display
if
the
INCREASE
SPEED
or
PROGRAM
START
button
is
pressed
and
no
movement
of
the
walking
belt
is
detected
within
seven
seconds.
Remove
the
key,
wait
for
ten
seconds,
and
then
reinsert
the
key.
Make
sure
that
you
stand
on
the
side
rails
of
the
treadmill
each
time
you
start
walking
belt.
If
the
error
code
appears
again,
call
our
toll
-free
HELPLINE.
Do
not
operate
the
treadmill
until
the
problem
is
corrected.
c.
Error
code
"E3"
may
appear
in
the
SPEED
display
if
the
speed
of
the
walking
belt
surges
above
the
selected
speed
setting.
Remove
the key,
wait
for
ten
seconds,
and
then
reinsert
the
key.
If
the
error
code
appears
again,
call
our
toll
-free
HELPLINE.
Do
not
operate
the
treadmill
until
the
problem
is
corrected.
d.
Error
code
"E4"
may
appear
in
the
SPEED
display
if
the
walking
belt
is
moving
at
a
slow
speed,
and
there
is
excessive
stress
on
the
motor.
Remove
the
key,
wait
for
ten
seconds,
and
then
reinsert
the
key.
If
you
weigh
over
200
pounds,
it
may
be
helpful
to
increase
the
incline
of
the
treadmill.
If
the
error
code
appears
again,
call
our
toll
-free
HELPLINE.
Do
not
operate
the
treadmill
until
the
problem
is
corrected.