HP EliteOne 700 Maintenance & Service Guide - Page 80

NFC sensor board

Get HP EliteOne 700 PDF manuals and user guides View all HP EliteOne 700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

NFC sensor board The NFC sensor board is located just above the right speaker (when viewed from behind). The NFC sensor board is housed inside of a plastic holder and has two small cables connected to it. The location of the board and an image of the board housed in its holder is shown in the following images. To remove the NFC sensor board: 1. Prepare the computer for disassembly (see Preparing to disassemble the computer on page 27). 2. Remove the stand (see Stand on page 29). 3. Remove the access panel (see Access panel on page 33). 4. Remove the lower rear panel (see Lower rear panel on page 59). 5. Disconnect the large right connector (1) and smaller left connector (2). NOTE: The cables and connectors on this board are small and fragile. Use care when disconnecting/ connecting the cables to avoid breaking the connectors on the board. 6. Press to disengage the tab (3) that secures the plastic housing that secures the board to the computer. 70 Chapter 5 Removal and Replacement Procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
NFC sensor board
The NFC sensor board is located just above the right speaker (when viewed from behind). The NFC sensor
board is housed inside of a plastic holder and has two small cables connected to it. The location of the board
and an image of the board housed in its holder is shown in the following images.
To remove the NFC sensor board:
1.
Prepare the computer for disassembly (see
Preparing to disassemble the computer
on page
27
).
2.
Remove the stand (see
Stand
on page
29
).
3.
Remove the access panel (see
Access panel
on page
33
).
4.
Remove the lower rear panel (see
Lower rear panel
on page
59
).
5.
Disconnect the large right connector
(1)
and smaller left connector
(2)
.
NOTE:
The cables and connectors on this board are small and fragile. Use care when disconnecting/
connecting the cables to avoid breaking the connectors on the board.
6.
Press to disengage the tab
(3)
that secures the plastic housing that secures the board to the computer.
70
Chapter 5
Removal and Replacement Procedures
ENWW