Home » HP Manuals » Desktops » HP EliteOne 700 » Manual Viewer

HP EliteOne 700 Maintenance & Service Guide - Page 108

Computer Setup—Security, Table 6-3

Add to My Manuals
Save this manual to your list of manuals

Page 108 highlights

Computer Setup-Security NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration. Table 6-3 Computer Setup-Security Option Description Setup Password Allows you to set and enable a setup (administrator) password. NOTE: If the setup password is set, it is required to change Computer Setup options, flash the ROM, and make changes to certain plug and play settings under Windows. Power-On Password Allows you to set and enable a power-on password. The power-on password prompt appears after a power cycle or reboot. If the user does not enter the correct power-on password, the unit will not boot. Password Options Allows you to enable/disable: (This selection appears only if a power-on password or setup password is set.) ● Lock Legacy Resources (determines whether or not Windows Device Manager is allowed to change resource settings for serial and parallel ports). ● Stringent security (enabling the stringent password disables the ability to reset the password by moving the jumper on the system board). Default is disabled. CAUTION: If you enable the stringent security feature and you forget the setup password or the power-on password, the computer is inaccessible and can no longer be used. If you lose or forget the password, the system board must be replaced. This scenario is not covered under warranty. To prevent the computer from becoming permanently unusable, record your configured setup password or power-on password in a safe place away from your computer. Without these passwords, the computer cannot be unlocked. ● Setup Browse Mode (appears if a setup password is set) (allows viewing, but not changing, the F10 Setup Options without entering setup password). Default is enabled. ● Password prompt on F9 & F12 (requires setup password to use these boot functions). Default is enabled. ● Network Server Mode. Default is disabled. Smart Cover Allows you to: ● Lock/unlock the Cover Lock. ● Set the Cover Removal Sensor to Disable/Notify User/Setup Password. NOTE: Notify User alerts the user that the sensor has detected that the cover has been removed. Setup Password requires that the setup password be entered to boot the computer if the sensor detects that the cover has been removed. Device Security Allows you to set Device Available/Device Hidden (default is Device Available) for: ● Embedded security device ● System audio NOTE: Set this value to 'Device hidden' to disable all system volume. ● Network controller NOTE: You must disable AMT before trying to hide the network controller. ● SATA ports (varies by model) 98 Chapter 6 Computer Setup (F10) Utility ENWW

Section	Page
Product features	11
Overview	11
Front components	13
Side components	14
Rear components	15
Positioning the computer	16
Adjusting the height-adjustable/reclining stand (optional)	17
Adjusting the tilt/swivel stand (optional)	18
Activating and Customizing the Software	19
Activating and customizing the software in Windows 7	19
Activating the Windows operating system	19
Downloading Windows 7 updates	19
Installing or upgrading device drivers	20
Customizing the monitor display	20
Activating and customizing the software in Windows 8	20
Activating the Windows Operating System	20
Downloading Windows 8 updates	20
Customizing the monitor display	21
Illustrated parts catalog	23
System parts	23
Keyboards and mice	24
Misc parts	25
Mass storage devices	26
Boards	27
Cables	28
Routine care, SATA drive guidelines, and disassembly preparation	29
Electrostatic discharge information	29
Generating static	30
Preventing electrostatic damage to equipment	30
Personal grounding methods and equipment	30
Grounding the work area	31
Recommended materials and equipment	31
Operating guidelines	32
Routine care	32
General cleaning safety precautions	32
Cleaning the Computer Case	33
Cleaning the keyboard	33
Cleaning the monitor	34
Cleaning the mouse	34
Service considerations	34
Power supply fan	34
Tools and software Requirements	34
Screws	34
Cables and connectors	35
Hard Drives	35
Lithium coin cell battery	35
SATA hard drive cables	36
SATA data cable	36
Cable management	36
Removal and Replacement Procedures	37
Preparing to disassemble the computer	37
Removing the rear I/O cover	38
Stand	39
Height-adjustable/recline stand (optional)	39
Tilt/swivel stand (optional)	41
Installing an access panel security screw	42
Access panel	43
Drives	44
Replacing a hard disc drive	44
Removing a 2.5-inch hard disc drive	45
Installing a 2.5-inch hard disc drive	46
Replacing the optical drive	49
mSATA Solid-State Drive	52
Memory	54
Battery	57
WLAN module	59
Heat sink	61
Processor	63
Top rear trim	64
Webcam module	65
Antenna	67
Lower rear panel	69
Fan assembly	71
Speakers	73
Converter board	76
Power button board	78
NFC sensor board	80
VESA mounting plate	82
Power supply	84
Side panels	86
System board	88
System board callouts	92
Card reader board	94
Front bezel and display panel	95
Hard drive and optical drive cables and connectors	101
Computer Setup (F10) Utility	103
Computer Setup (F10) Utilities	103
Using Computer Setup (F10) Utilities	104
Computer Setup—File	105
Computer Setup—Storage	106
Computer Setup—Security	108
Computer Setup—Power	112
Computer Setup—Advanced	113
Recovering the Configuration Settings	116
HP PC Hardware Diagnostics	117
Why run HP PC Hardware Diagnostics	117
How to access and run HP PC Hardware Diagnostics	117
Downloading HP PC Hardware Diagnostics (UEFI) to a USB device	118
Troubleshooting without diagnostics	119
Safety and comfort	119
Before you call for technical support	119
Helpful hints	120
Solving general problems	122
Solving power problems	126
Solving hard drive problems	127
Solving media card reader problems	129
Solving display problems	130
Solving audio problems	136
Solving printer problems	138
Solving keyboard and mouse problems	139
Solving hardware installation problems	141
Solving network problems	143
Solving memory problems	146
Solving processor problems	148
Solving CD-ROM and DVD problems	148
Solving USB flash drive problems	150
Solving front panel component problems	151
Solving Internet access problems	152
Solving software problems	153
System backup and recovery	155
Backing up, restoring, and recovering in Windows 8	155
Creating recovery media and backups	155
Restoring and recovering using Windows 8 tools	156
Using Windows 8 Refresh	156
Using Windows 8 Reset	157
Recovery using the Windows 8 recovery USB flash drive	158
Recovery using Windows 8 operating system media (purchased separately)	158
Backing up, restoring, and recovering in Windows 7	160
Creating recovery media	160
Creating recovery media using HP Recovery Manager (select models only)	161
Creating recovery discs with HP Recovery Disc Creator (select models only)	162
Creating recovery discs	162
Backing up your information	162
System Restore	163
System Recovery	163
System Recovery when Windows is responding	164
System Recovery when Windows is not responding	164
System Recovery using recovery media (select models only)	165
Using HP Recovery Disc operating system discs (select models only)	165
POST error messages	167
POST numeric codes and text messages	168
Interpreting POST diagnostic front panel LEDs	175
Password security and resetting CMOS	179
Resetting the password jumper	180
Establishing a setup or power-on password	181
Resetting the setup and power-on password	181
Changing a setup or power-on password	182
Clearing and resetting the CMOS	182
Power cord set requirements	185
General requirements	185
Japanese power cord requirements	185
Country-specific requirements	186
Statement of Volatility	187
Specifications	189

Match case Limit results 1 per page

Computer Setup—Security

NOTE:

Support for specific Computer Setup options may vary depending on the hardware configuration.

Table 6-3

Computer Setup—Security

Option

Description

Setup Password

Allows you to set and enable a setup (administrator) password.

NOTE:

If the setup password is set, it is required to change Computer Setup options, flash the ROM, and

make changes to certain plug and play settings under Windows.

Power-On Password

Allows you to set and enable a power-on password. The power-on password prompt appears after a

power cycle or reboot. If the user does not enter the correct power-on password, the unit will not boot.

Password Options

(This selection appears

only if a power-on

password or setup

password is set.)

Allows you to enable/disable:

●

Lock Legacy Resources (determines whether or not Windows Device Manager is allowed to change

resource settings for serial and parallel ports).

●

Stringent security (enabling the stringent password disables the ability to reset the password by

moving the jumper on the system board). Default is disabled.

CAUTION:

If you enable the stringent security feature and you forget the setup password or the

power-on password, the computer is inaccessible and can no longer be used.

If you lose or forget the password, the system board must be replaced. This scenario is not covered

under warranty.

To prevent the computer from becoming permanently unusable, record your configured setup

password or power-on password in a safe place away from your computer. Without these

passwords, the computer cannot be unlocked.

●

Setup Browse Mode (appears if a setup password is set) (allows viewing, but not changing, the F10

Setup Options without entering setup password). Default is enabled.

●

Password prompt on F9 & F12 (requires setup password to use these boot functions). Default is

enabled.

●

Network Server Mode. Default is disabled.

Smart Cover

Allows you to:

●

Lock/unlock the Cover Lock.

●

Set the Cover Removal Sensor to Disable/Notify User/Setup Password.

NOTE:

Notify User

alerts the user that the sensor has detected that the cover has been removed.

Setup

Password

requires that the setup password be entered to boot the computer if the sensor detects that

the cover has been removed.

Device Security

Allows you to set Device Available/Device Hidden (default is Device Available) for:

●

Embedded security device

●

System audio

NOTE:

Set this value to ‘Device hidden’ to disable all system volume.

●

Network controller

NOTE:

You must disable AMT before trying to hide the network controller.

●

SATA ports (varies by model)

Chapter 6

Computer Setup (F10) Utility

ENWW