Gastroback 41402 User Manual - Page 13

Troubleshooting

Get Gastroback 41402 PDF manuals and user guides View all Gastroback 41402 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

8. The motor block must only be wiped clean with a moist cloth. Do not clean the motor block under flowing water, nor should it be immersed in water! Do not use alcohol, benzene, etc.! 9. Grease the grinding disc and knife with cooking oil to prevent air corrosion. Troubleshooting Possible problem Easy solution The mince is not fine enough. Use a smaller grinding disc and/or mince the ingredients more then once. There are still ingredients in the feed tube The mincer is blocked. Turn the appliance off immediately and operate but no mince is coming out of the mincer. according to the instructions ›Clear a blocking‹. The motor stops running while operating. The overload protection might got activated. Turn the appliance off immediately and operate according to the instructions ›Clear a blocking‹. After cleaning the motor does not get started again when turning the appliance on. • Is the power cord plugged in? • The motor might be blocked with some hard substance (for example a bone). Turn the appliance off immediately and pull the plug. • Disassemble and clean the appliance. Operate according to the instructions ›Care and cleaning‹. • If the problem is not solved after the cleaning, take the appli- ance for technical maintenance and repair to an authorised service centre. The mincer blocks up permanently while operating. • To ensure that the mincer does not seize, never operate it under excessive pressure. Operate in a slow and constant pace. Do not try to rush the procedure by pushing down the meat with force. • For mincing hard ingredients really fine start with the grinding disc with the bigger holes. Mincing the second time use the finer mincer plate. The worm housing moves or loosened while The screw plug loosened. Turn the appliance off immediately. Press the operating. worm housing with one hand against the motor housing using the other hand to tighten the screw plug turning it clockwise. The mince leaks out at the side of the closing ring. The closing ring is not screwed on tight enough. Turn the appliance off immediately and then pull the plug. Tighten the closing ring but do not overwind the winding. If the problem still occurs disassemble and clean the appliance. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
8. The motor block must only be wiped clean with a moist cloth. Do not clean the motor block
under flowing water, nor should it be immersed in water! Do not use alcohol, benzene, etc.!
9. Grease the grinding disc and knife with cooking oil to prevent air corrosion.
TROUBLESHOOTING
Possible problem
Easy solution
The mince is not fine enough.
Use a smaller grinding disc and/or mince the ingredients more
then once.
There are still ingredients in the feed tube
but no mince is coming out of the mincer.
The mincer is blocked. Turn the appliance off immediately and operate
according to the instructions ›Clear a blocking‹.
The motor stops running while operating.
The overload protection might got activated. Turn the appliance
off immediately and operate according to the instructions ›Clear
a blocking‹.
After cleaning the motor does not get started
again when turning the appliance on.
• Is the power cord plugged in?
•
The motor might be blocked with some hard substance (for example
a bone). Turn the appliance off immediately and pull the plug.
•
Disassemble and clean the appliance. Operate according to the
instructions ›Care and cleaning‹.
•
If the problem is not solved after the cleaning, take the appli-
ance for technical maintenance and repair to an authorised
service centre.
The mincer blocks up permanently while
operating.
•
To ensure that the mincer does not seize, never operate it
under excessive pressure. Operate in a slow and constant
pace. Do not try to rush the procedure by pushing down the
meat with force.
•
For mincing hard ingredients really fine start with the grinding disc
with the bigger holes. Mincing the second time use the finer mincer
plate.
The worm housing moves or loosened while
operating.
The screw plug loosened. Turn the appliance off immediately. Press the
worm housing with one hand against the motor housing using the other
hand to tighten the screw plug turning it clockwise.
The mince leaks out at the side of the clos-
ing ring.
The closing ring is not screwed on tight enough. Turn the appliance off
immediately and then pull the plug. Tighten the closing ring but do not
overwind the winding. If the problem still occurs disassemble and clean
the appliance.
29