Garmin Tread XL - Baja Race Edition Owners Manual - Page 74

Connecting the Device to Vehicle Power

Get Garmin Tread XL - Baja Race Edition PDF manuals and user guides View all Garmin Tread XL - Baja Race Edition manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Connecting the Device to Vehicle Power You should always confirm all electrical connections are secure and will not come loose while operating the device. NOTICE If the ignition wire is not used, do not tie the ignition to the positive terminal on the vehicle battery. Ground the ignition wire or leave it disconnected. Failure to ground or disconnect the ignition wire when the ignition is not used could prevent the device from powering on. 1 Remove the terminal cover using a Phillips screwdriver. 2 Remove the screws from the GND terminal and the +12V terminal . 3 Connect the large ring end of the included ground wire to the negative terminal on the vehicle battery. 4 Connect the small ring end of the ground wire to the GND terminal on the device. 5 Tighten the screw on the GND terminal. You should confirm the screws cannot be loosened by hand. 6 Connect the small ring end of the included 12V cable to the +12V terminal on the device. 7 Tighten the screw on the +12V terminal. You should confirm the screws cannot be loosened by hand. NOTICE Do not overtighten the screw on the +12V terminal to prevent damage to the terminal. 68 Appendix

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Connecting the Device to Vehicle Power
You should always confirm all electrical connections are secure and will not come loose while operating the
device.
NOTICE
If the ignition wire is not used, do not tie the ignition to the positive terminal on the vehicle battery. Ground the
ignition wire or leave it disconnected. Failure to ground or disconnect the ignition wire when the ignition is not
used could prevent the device from powering on.
1
Remove the terminal cover
using a Phillips screwdriver.
2
Remove the screws from the
GND
terminal and the
+12V
terminal
.
3
Connect the large ring end of the included ground wire
to the negative terminal on the vehicle battery.
4
Connect the small ring end of the ground wire to the
GND
terminal
on the device.
5
Tighten the screw on the GND terminal.
You should confirm the screws cannot be loosened by hand.
6
Connect the small ring end of the included 12V cable to the
+12V
terminal
on the device.
7
Tighten the screw on the +12V terminal.
You should confirm the screws cannot be loosened by hand.
NOTICE
Do not overtighten the screw on the +12V terminal to prevent damage to the terminal.
68
Appendix