Brother International TJ-4520TN Users Guide - Page 58

Gap/Black Mark Sensor Calibration, Self-Test, and Entering Dump Mode, Selection, amber 5 times

Get Brother International TJ-4520TN PDF manuals and user guides View all Brother International TJ-4520TN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

6.1.2 Gap/Black Mark Sensor Calibration, Self-Test, and Entering Dump Mode Calibrate the Gap or Black Mark Sensor if the sensor's settings used in the last print job are not suitable for the current print job. During the calibration of the Gap/Black Mark Sensor, the printer detects the label length, prints the internal configuration (self-test), and then enters Dump Mode. To calibrate the Gap/Black Mark Sensor: 1. Turn off the printer. 2. Press and hold the right Selection button, and then turn on the Power Switch. 3. Release the button when Self-test appears on the screen. Note The LED color will change as follows: Amber (lit)  red (5 times)  amber (5 times)  green (5 times)  green/amber (5 times)  red/amber (5 times)  green (lit) 4. The printer calibrates the sensor and detects the label length, prints the internal settings, and then enters Dump Mode. Note To select the sensor for calibration, send the correct command to the printer:  For the Gap Sensor: send the GAP command  For the Black Mark Sensor: send the BLINE command For more information about the available commands, see the FBPL Command Reference on your model's Manuals page at support.brother.com. 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
54
6.1.2
Gap/Black Mark Sensor Calibration, Self-Test, and Entering Dump Mode
Calibrate the Gap or Black Mark Sensor if the sensor's settings used in the last print job are not
suitable for the current print job. During the calibration of the Gap/Black Mark Sensor, the printer
detects the label length, prints the internal configuration (self-test), and then enters Dump Mode.
To calibrate the Gap/Black Mark Sensor:
1.
Turn off the printer.
2.
Press and hold the right
Selection
button, and then turn on the Power Switch.
3.
Release the button when
Self-test
appears on the screen.
Note
The LED color will change as follows:
Amber (lit)
red (5 times)
amber (5 times)
green (5 times)
green/amber (5 times)
red/amber (5 times)
green (lit)
4.
The printer calibrates the sensor and detects the label length, prints the internal settings,
and then enters Dump Mode.
Note
To select the sensor for calibration, send the correct command to the printer:
For the Gap Sensor: send the GAP command
For the Black Mark Sensor: send the BLINE command
For more information about the available commands, see the
FBPL Command Reference
on
your model's
Manuals
page at
support.brother.com
.