Brother International TJ-4520TN Users Guide - Page 57

Ribbon and Gap/Black Mark Sensor Calibration, Selection, Sensor Calibration, red 5 times

Get Brother International TJ-4520TN PDF manuals and user guides View all Brother International TJ-4520TN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

6.1.1 Ribbon and Gap/Black Mark Sensor Calibration Calibrate the Gap/Black Mark Sensor sensitivity when:  You purchase a new printer.  You change label stock.  The label printer initializes. To calibrate the Ribbon and Gap/Black Mark Sensors: 1. Turn off the printer. 2. Press and hold the right Selection button, and then turn on the Power Switch. 3. Release the button when Sensor Calibration appears on the screen. Note  The LED color will change as follows: Amber (lit)  red (5 times)  amber (5 times)  green (5 times)  green/amber (5 times)  red/amber (5 times)  green (lit)  To select the sensor for calibration, send the correct command to the printer:  For the Gap Sensor: send the GAP command  For the Black Mark Sensor: send the BLINE command For more information about the available commands, see the FBPL Command Reference on your model's Manuals page at support.brother.com. 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
53
6.1.1 Ribbon and Gap/Black Mark Sensor Calibration
Calibrate the Gap/Black Mark Sensor sensitivity when:
You purchase a new printer.
You change label stock.
The label printer initializes.
To calibrate the Ribbon and Gap/Black Mark Sensors:
1.
Turn off the printer.
2.
Press and hold the right
Selection
button, and then turn on the Power Switch.
3.
Release the button when
Sensor Calibration
appears on the screen.
Note
The LED color will change as follows:
Amber (lit)
red (5 times)
amber (5 times)
green (5 times)
green/amber (5 times)
red/amber (5 times)
green (lit)
To select the sensor for calibration, send the correct command to the printer:
For the Gap Sensor: send the GAP command
For the Black Mark Sensor: send the BLINE command
For more information about the available commands, see the
FBPL Command Reference
on your model's
Manuals
page at
support.brother.com
.