2012 Yamaha Motorsports RS Vector L-TX Owners Manual - Page 113

2012 Yamaha Motorsports RS Vector L-TX Manual

Page 113 highlights

Periodic maintenance and adjustment 2. Use a Phillips screwdriver to turn the headlight beam adjusting screw and adjust the headlight beams. To lower the headlight beams, turn the headlight beam adjusting screw in direction (a). To raise the headlight beams, turn the headlight beam adjusting screw in direction (b). 1 2 1. Slot 2. Projection 10. Fit the weatherstrip on the headlight unit into the recess in the top of the air filter case cover. (b) 1 (a) 1. Headlight beam adjusting screw 3. 1. 2. Install the top cover. Open the shroud. Insert a Phillips screwdriver into the hole under the shroud to turn the headlight beam adjusting screw. To lower the headlight beams, turn the Phillips screwdriver in direction (a). To raise the headlight beams, turn the Phillips screwdriver in direction (b). RST90 1 1. Weatherstrip 11. Install the headlight unit bolts and windshield stay bolts, and then tighten them to their specified torques. Tightening torques: Headlight unit bolt: 3.0 Nm (0.30 m·kgf, 2.2 ft·lbf) Windshield stay bolt: 14 Nm (1.4 m·kgf, 10 ft·lbf) 12. Install the top cover and the shroud. ESU14150 Adjusting the headlight beams RS90P / RS90PLT / RST90PGT 1. Remove the top cover. (See page 63 for removal procedures.) 1. Headlight beam adjusting screw 107

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142

Periodic maintenance and adjustment
107
10.
Fit the weatherstrip on the headlight unit
into the recess in the top of the air filter
case cover.
11.
Install the headlight unit bolts and wind-
shield stay bolts, and then tighten them to
their specified torques.
12.
Install the top cover and the shroud.
ESU14150
Adjusting the headlight beams
RS90P / RS90PLT / RST90PGT
1.
Remove the top cover. (See page 63 for
removal procedures.)
2.
Use a Phillips screwdriver to turn the
headlight beam adjusting screw and ad-
just the headlight beams. To lower the
headlight beams, turn the headlight
beam adjusting screw in direction (a). To
raise the headlight beams, turn the head-
light beam adjusting screw in direction
(b).
3.
Install the top cover.
RST90
1.
Open the shroud.
2.
Insert a Phillips screwdriver into the hole
under the shroud to turn the headlight
beam adjusting screw. To lower the
headlight beams, turn the Phillips screw-
driver in direction (a). To raise the head-
light beams, turn the Phillips screwdriver
in direction (b).
1. Slot
2. Projection
1. Weatherstrip
Tightening torques:
Headlight unit bolt:
3.0 Nm (0.30 m·kgf, 2.2 ft·lbf)
Windshield stay bolt:
14 Nm (1.4 m·kgf, 10 ft·lbf)
1
2
1
1.
Headlight beam adjusting screw
1.
Headlight beam adjusting screw
1
(b)
(a)