2011 Yamaha Motorsports RS Venture GT Owners Manual - Page 73

2011 Yamaha Motorsports RS Venture GT Manual

Get 2011 Yamaha Motorsports RS Venture GT PDF manuals and user guides View all 2011 Yamaha Motorsports RS Venture GT manuals

Page 73 highlights

Periodic maintenance and adjustment 2 1 3. 4. 5. 6. 7. Tighten the quick fastener screws. Place the windshield stay rubber covers in their original position. Install the handlebar cover. Connect the auxiliary DC jack coupler. Install the left side cover and the shroud. 1. Shroud latch 2. Shroud To close the shroud Slowly lower the shroud to its original position, and then hook the shroud latches. Right side cover To remove the right side cover 1. Open the shroud. (See the above procedure.) 2. Remove the screws and bolts, and then remove the right side cover. ECS00372 NOTICE G G Make sure that all cables, hoses and leads are routed properly before installing the shroud and covers. When installing the shroud and covers, be sure to tighten the fasteners securely. 3 ESU13962 Opening and closing the shroud and removing and installing the right side cover (RST90) EWS00810 1 1. Screw 2. Bolt 3. Right side cover 2 1 WARNING Be sure the shroud and right side cover are secured before operation. A loose shroud or cover could move and cause loss of control. Shroud To open the shroud Unhook the shroud latches, and then slowly raise the shroud forward until it stops. To install the right side cover 1. Place the right side cover in the original position, and then tighten the bolts and screws. 2. Close the shroud. 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Periodic maintenance and adjustment
67
3.
Tighten the quick fastener screws.
4.
Place the windshield stay rubber covers
in their original position.
5.
Install the handlebar cover.
6.
Connect the auxiliary DC jack coupler.
7.
Install the left side cover and the shroud.
NOTICE
ECS00372
●
Make sure that all cables, hoses and
leads are routed properly before install-
ing the shroud and covers.
●
When installing the shroud and covers,
be sure to tighten the fasteners secure-
ly.
ESU13962
Opening and closing the
shroud and removing and in-
stalling the right side cover
(RST90)
WARNING
EWS00810
Be sure the shroud and right side cover
are secured before operation. A loose
shroud or cover could move and cause
loss of control.
Shroud
To open the shroud
Unhook the shroud latches, and then slowly
raise the shroud forward until it stops.
To close the shroud
Slowly lower the shroud to its original position,
and then hook the shroud latches.
Right side cover
To remove the right side cover
1.
Open the shroud. (See the above proce-
dure.)
2.
Remove the screws and bolts, and then
remove the right side cover.
To install the right side cover
1.
Place the right side cover in the original
position, and then tighten the bolts and
screws.
2.
Close the shroud.
1.
Shroud latch
2. Shroud
1. Screw
2. Bolt
3.
Right side cover
2
1
1
3
2
1