2011 Yamaha Motorsports RS Venture GT Owners Manual - Page 31

2011 Yamaha Motorsports RS Venture GT Manual

Get 2011 Yamaha Motorsports RS Venture GT PDF manuals and user guides View all 2011 Yamaha Motorsports RS Venture GT manuals

Page 31 highlights

Control functions Maximum rated capacity: DC 12 V, 2.5 A (30 W) ESU13264 Maximum rated capacity: DC 12 V, 1.5 A (18 W) ESU10571 Helmet shield heater jack (RS90GT / RS90LTGT / RST90GT) The helmet shield heater jack is located on the left side of the handlebar. Brake lever The snowmobile is stopped by braking the entire drive system. Squeeze the brake lever towards the handlebar grip to stop the snowmobile. TIP The helmet shield heater jack can only be used if the engine is running. To use the helmet shield heater jack 1. 2. Start the engine. Open the helmet shield heater jack cap, and then insert the power plug of the helmet shield heater into the jack. 1 2 1. Brake lever TIP When the brake lever is squeezed, the brake light comes on. ECS00060 NOTICE Make sure that the brake lever end does not project out over the handlebar end. This will help prevent brake lever damage when the snowmobile is placed on its side for service. 1. Helmet shield heater jack cap 2. Helmet shield heater jack 3. After using the helmet shield heater, be sure to remove its power plug from the jack and to close the jack cap. RS90GT / RS90LTGT The brake lever is equipped with a position adjuster. To adjust the brake lever position: 1. Loosen the locknut. 2. While lightly pushing the brake lever in direction (a), turn the adjusting bolt to set the brake lever to the desired position. ECS00892 NOTICE To avoid circuit overload and a possible fuse blowing, do not use a helmet shield heater requiring more than the maximum rated capacity for the helmet shield heater jack. (See page 109 for the specified fuse amperage.) 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Control functions
25
ESU13264
Helmet shield heater jack
(RS90GT / RS90LTGT /
RST90GT)
The helmet shield heater jack is located on
the left side of the handlebar.
TIP
The helmet shield heater jack can only be
used if the engine is running.
To use the helmet shield heater jack
1.
Start the engine.
2.
Open the helmet shield heater jack cap,
and then insert the power plug of the hel-
met shield heater into the jack.
3.
After using the helmet shield heater, be
sure to remove its power plug from the
jack and to close the jack cap.
NOTICE
ECS00892
To avoid circuit overload and a possible
fuse blowing, do not use a helmet shield
heater requiring more than the maximum
rated capacity for the helmet shield heater
jack. (See page 109 for the specified fuse
amperage.)
ESU10571
Brake lever
The snowmobile is stopped by braking the en-
tire drive system.
Squeeze the brake lever towards the handle-
bar grip to stop the snowmobile.
TIP
When the brake lever is squeezed, the brake
light comes on.
NOTICE
ECS00060
Make sure that the brake lever end does
not project out over the handlebar end.
This will help prevent brake lever damage
when the snowmobile is placed on its side
for service.
RS90GT / RS90LTGT
The brake lever is equipped with a position
adjuster.
To adjust the brake lever position:
1.
Loosen the locknut.
2.
While lightly pushing the brake lever in di-
rection (a), turn the adjusting bolt to set
the brake lever to the desired position.
Maximum rated capacity:
DC 12 V, 2.5 A (30 W)
1.
Helmet shield heater jack cap
2.
Helmet shield heater jack
1
2
Maximum rated capacity:
DC 12 V, 1.5 A (18 W)
1.
Brake lever