2009 Yamaha Motorsports RS Venture Owners Manual - Page 57

2009 Yamaha Motorsports RS Venture Manual

Get 2009 Yamaha Motorsports RS Venture PDF manuals and user guides View all 2009 Yamaha Motorsports RS Venture manuals

Page 57 highlights

Periodic maintenance and adjustment 1. Edge of the secondary sheave assembly 2. V-belt position Standard V-belt position: From 1.5 mm (0.06 in) above the edge of the secondary sheave assembly to 0.5 mm (0.02 in) below the edge 6. If the V-belt position is incorrect, adjust it by removing or adding a spacer on each V-belt position adjusting bolt. 1. V-belt position adjusting bolt 2. Spacer V-belt position More than 1.5 mm (0.06 in) above the edge From 1.5 mm (0.06 in) above the edge to 0.5 mm (0.02 in) below the edge More than 0.5 mm (0.02 in) below the edge Adjustment Remove spacer Not necessary (It is correct.) Add spacer 7. Tighten the V-belt position adjusting bolts. V-belt position adjusting bolt tightening torque: 10 Nm (1.0 m·kgf, 7.2 ft·lbf) 8. Install the V-belt over the primary sheave assembly. 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Periodic maintenance and adjustment
51
6.
If the V-belt position is incorrect, adjust it
by removing or adding a spacer on each
V-belt position adjusting bolt.
7.
Tighten the V-belt position adjusting
bolts.
8.
Install the V-belt over the primary sheave
assembly.
1.
Edge of the secondary sheave assembly
2.
V-belt position
Standard V-belt position:
From 1.5 mm (0.06 in) above the edge
of the secondary sheave assembly to
0.5 mm (0.02 in) below the edge
1.
V-belt position adjusting bolt
2. Spacer
V-belt position
Adjustment
More than 1.5 mm
(0.06 in) above the
edge
Remove spacer
From 1.5 mm (0.06 in)
above the edge to 0.5
mm (0.02 in) below
the edge
Not necessary (It is
correct.)
More than 0.5 mm
(0.02 in) below the
edge
Add spacer
V-belt position adjusting bolt tightening
torque:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)