2008 Yamaha Motorsports Morphous Owners Manual - Page 60

2008 Yamaha Motorsports Morphous Manual

Get 2008 Yamaha Motorsports Morphous PDF manuals and user guides View all 2008 Yamaha Motorsports Morphous manuals

Page 60 highlights

PERIODIC MAINTENANCE AND MINOR REPAIR Tightening torque: Oil filter element cover bolt: 10 Nm (1.0 m·kgf, 7.2 ft·lbf) Recommended engine oil: See page 8-1. Oil quantity: Without oil filter element replacement: 1.50 L (1.59 US qt) (1.32 Imp.qt) With oil filter element replacement: 1.70 L (1.80 US qt) (1.50 Imp.qt) 11. Reset the oil change indicator according to the following procedure. To reset the oil change indicator 1. Turn the key to "ON". 2. Hold the "OIL CHANGE" button pushed for at least three seconds. 1 2 3 4 5 6 7 8 9 NOTE: Make sure that the O-rings are properly seated. 8. Install the washer and the engine oil drain bolt, and then tighten the drain bolt to the specified torque. Tightening torque: Engine oil drain bolt: 20 Nm (2.0 m·kgf, 14.5 ft·lbf) NOTE: Be sure to wipe off spilled oil on any parts after the engine and exhaust system have cooled down. ECA11670 NOTE: Make sure that the washer is properly seated. 9. Add the specified amount of the recommended engine oil, and then install and tighten the oil filler cap. CAUTION: G Do not use oils with a diesel specification of "CD" or oils of a higher quality than specified. In addition, do not use oils labeled "ENERGY CONSERVING II" or higher. G Be sure no foreign material enters the crankcase. 10. Start the engine, and then let it idle for several minutes while checking it for oil leakage. If oil is leaking, immediately turn the engine off and check for the cause. 6-18 1 1. "OIL CHANGE" button 3. Release the "OIL CHANGE" button, and the oil change indicator will go off. NOTE: If the engine oil is changed before the oil change indicator comes on (i.e. before the periodic oil change interval has been reached), the indicator must be reset after the oil change for the next periodic oil change to be indicated at

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
PERIODIC MAINTENANCE AND MINOR REPAIR
6-18
1
2
3
4
5
6
7
8
9
NOTE:
Make sure that the O-rings are properly
seated.
8. Install the washer and the engine
oil drain bolt, and then tighten the
drain bolt to the specified torque.
NOTE:
Make sure that the washer is properly
seated.
9. Add the specified amount of the
recommended engine oil, and then
install and tighten the oil filler cap.
NOTE:
Be sure to wipe off spilled oil on any
parts after the engine and exhaust sys-
tem have cooled down.
CAUTION:
ECA11670
±
Do not use oils with a diesel
specification of
“
CD
”
or oils of a
higher quality than specified. In
addition, do not use oils labeled
“
ENERGY CONSERVING II
”
or
higher.
±
Be sure no foreign material en-
ters the crankcase.
10. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking, im-
mediately turn the engine off and
check for the cause.
11. Reset the oil change indicator ac-
cording to the following procedure.
To reset the oil change indicator
1. Turn the key to
“
ON
”
.
2. Hold the
“
OIL CHANGE
”
button
pushed for at least three seconds.
3. Release the
“
OIL CHANGE
”
but-
ton, and the oil change indicator
will go off.
NOTE:
If the engine oil is changed before the
oil change indicator comes on (i.e. be-
fore the periodic oil change interval has
been reached), the indicator must be
reset after the oil change for the next
periodic oil change to be indicated at
Tightening torque:
Oil filter element cover bolt:
10 Nm (1.0 m
·
kgf, 7.2 ft
·
lbf)
Tightening torque:
Engine oil drain bolt:
20 Nm (2.0 m
·
kgf, 14.5 ft
·
lbf)
Recommended engine oil:
See page 8-1.
Oil quantity:
Without oil filter element replace-
ment:
1.50 L (1.59 US qt) (1.32 Imp.qt)
With oil filter element replacement:
1.70 L (1.80 US qt) (1.50 Imp.qt)
1.
“
OIL CHANGE
”
button
1