2007 Yamaha Motorsports Phazer FX Owners Manual - Page 69

2007 Yamaha Motorsports Phazer FX Manual

Get 2007 Yamaha Motorsports Phazer FX PDF manuals and user guides View all 2007 Yamaha Motorsports Phazer FX manuals

Page 69 highlights

8. Install the engine oil drain bolts, and then tighten them to the specified torques. Tightening torques: Crankcase engine oil drain bolt: 30 Nm (3.0 m·kgf, 22 ft·lb) Oil tank engine oil drain bolt: 16 Nm (1.6 m·kgf, 11 ft·lb) 9. Add 1.5 L (1.3 Imp qt, 1.6 US qt) of the recommended engine oil to the oil tank, and then install and tighten the oil level gauge/dipstick. Recommended engine oil: See page 6-2. Oil quantity: With oil filter cartridge replacement: 2.63 L (2.31 Imp qt, 2.78 US qt) Without oil filter cartridge replacement: 2.45 L (2.16 Imp qt, 2.59 US qt) Total amount: 3.00 L (2.64 Imp qt, 3.17 US qt) 10. Start the engine, warm it up for several minutes, and then turn it off. 11. Add sufficient oil of the recommended type to raise it to the "H" level mark on the oil level gauge/dipstick. (See pages 6-3-6-4 for the checking procedure.) CAUTION: @ G G @ When adding the engine oil, be careful not to fill above the "H" level mark on the oil level gauge/ dipstick. Make sure that no foreign material enters the engine oil tank. 12. Start the engine, and then let it idle for several minutes while checking it for oil leakage. If oil is leaking, immediately turn the engine off and make sure that the engine oil drain bolts and oil level gauge/dipstick are installed correctly. 13. Turn the engine off, and then connect the oil level gauge coupler. 8-14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
8-14
8. Install the engine oil drain bolts, and then tighten
them to the specified torques.
9. Add 1.5 L (1.3 Imp qt, 1.6 US qt) of the recom-
mended engine oil to the oil tank, and then install and
tighten the oil level gauge/dipstick.
10. Start the engine, warm it up for several minutes, and
then turn it off.
11. Add sufficient oil of the recommended type to raise it
to the “H” level mark on the oil level gauge/dipstick.
(See pages 6-3–6-4 for the checking procedure.)
CAUTION
:
@
●
When adding the engine oil, be careful not to fill
above the “H” level mark on the oil level gauge/
dipstick.
●
Make sure that no foreign material enters the
engine oil tank.
@
12. Start the engine, and then let it idle for several min-
utes while checking it for oil leakage. If oil is leaking,
immediately turn the engine off and make sure that
the engine oil drain bolts and oil level gauge/dipstick
are installed correctly.
13. Turn the engine off, and then connect the oil level
gauge coupler.
Tightening torques:
Crankcase engine oil drain bolt:
30 Nm (3.0 m·kgf, 22 ft·lb)
Oil tank engine oil drain bolt:
16 Nm (1.6 m·kgf, 11 ft·lb)
Recommended engine oil:
See page 6-2.
Oil quantity:
With oil filter cartridge replacement:
2.63 L (2.31 Imp qt, 2.78 US qt)
Without oil filter cartridge replacement:
2.45 L (2.16 Imp qt, 2.59 US qt)
Total amount:
3.00 L (2.64 Imp qt, 3.17 US qt)