2006 Yamaha Motorsports Apex GT Owners Manual - Page 85

2006 Yamaha Motorsports Apex GT Manual

Get 2006 Yamaha Motorsports Apex GT PDF manuals and user guides View all 2006 Yamaha Motorsports Apex GT manuals

Page 85 highlights

ESU04092 Adjusting the control rods The weight transfer can be adjusted by turning the control rod adjuster or adjusting nut. For RX10GT 1. Loosen the locknut 1. 2. Turn the control rod adjuster 2 in direction a to increase weight transfer or direction b to decrease weight transfer. CD-27E Adjuster turning direction Weight transfer a Increased ← ← → b → Decreased 3. Check the adjuster length c using the scale on the special wrench 3 included in the owner's tool kit as shown. Make sure that the rim d of the control rod body is within the range e of the scale. 4. Tighten the locknut while holding the adjuster in place. Locknut tightening torque: 35 Nm (3.5 m·kgf, 25 ft·lb) CAUTION: @ When using the special wrench, make sure that it is situated at a right angle to the control rod, and that it is tightly fitted to the locknut or the control rod adjuster. @ WARNING @ Never adjust the control rod beyond the range of the scale on the special wrench. @ 8-27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
8-27
ESU04092
Adjusting the control rods
The weight transfer can be adjusted by turning the con-
trol rod adjuster or adjusting nut.
For RX10GT
1. Loosen the locknut
1
.
2. Turn the control rod adjuster
2
in direction
a
to
increase weight transfer or direction
b
to decrease
weight transfer.
CD-27E
3. Check the adjuster length
c
using the scale on the
special wrench
3
included in the owner’s tool kit as
shown. Make sure that the rim
d
of the control rod
body is within the range
e
of the scale.
4. Tighten the locknut while holding the adjuster in
place.
CAUTION
:
@
When using the special wrench, make sure that it is
situated at a right angle to the control rod, and that it
is tightly fitted to the locknut or the control rod
adjuster.
@
WARNING
@
Never adjust the control rod beyond the range of the
scale on the special wrench.
@
Adjuster turning
direction
a
←
→
b
Weight transfer
Increased
←
→
Decreased
Locknut tightening torque:
35 Nm (3.5 m·kgf, 25 ft·lb)