2014 Polaris 800 Pro RMK Owners Manual - Page 113

2014 Polaris 800 Pro RMK Manual

Get 2014 Polaris 800 Pro RMK PDF manuals and user guides View all 2014 Polaris 800 Pro RMK manuals

Page 113 highlights

MAINTENANCE Steering System Ski Skags WARNING! Worn skis and/or skags will adversely affect handling. Loss of vehicle control may result, causing serious injury or death. See your dealer's studding chart for recommended skags. If you install longer or more aggressive carbide skags than the original equipment, it may also be necessary to add track studs to maintain proper vehicle control while turning on hard-packed snow or ice. Check skags before each use of the snowmobile to ensure positive steering characteristics. Skags must be replaced when worn to half their original diameter. TIP: Carbide skags must be replaced if any abnormal wear or chipping is found. Skag Replacement 1. Raise and support the front of the snowmobile so the skis are approximately 6 inches (15.2 cm) from the ground. 2. Remove the attaching nuts and pry the skag downward. 3. Remove the front end of the skag. 4. Remove the rear end of the skag. 5. Reverse the steps to install a skag. Skag 111

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
111
MAINTENANCE
Steering System
Ski Skags
WARNING!
Worn skis and/or skags will adversely affect handling. Loss of
vehicle control may result, causing serious injury or death. See your dealer's
studding chart for recommended skags. If you install longer or more aggressive
carbide skags than the original equipment, it may also be necessary to add track
studs to maintain proper vehicle control while turning on hard-packed snow or
ice.
Check skags before each use of the snowmobile to ensure positive
steering characteristics. Skags must be replaced when worn to half their
original diameter.
TIP:
Carbide skags must be replaced if any abnormal wear or chipping is found.
Skag Replacement
1.
Raise and support the front
of the snowmobile so the
skis are approximately 6
inches (15.2 cm) from the
ground.
2.
Remove the attaching nuts
and pry the skag downward.
3.
Remove the front end of the
skag.
4.
Remove the rear end of the
skag.
5.
Reverse the steps to install a
skag.
Skag