2008 Ducati Superbike 848 Owners Manual

2008 Ducati Superbike 848 Manual

Get 2008 Ducati Superbike 848 PDF manuals and user guides View all 2008 Ducati Superbike 848 manuals

2008 Ducati Superbike 848 manual content summary:

  • 2008 Ducati Superbike 848 | Owners Manual - Page 1
    Use and maintenance manual E 848 1
  • 2008 Ducati Superbike 848 | Owners Manual - Page 2
    E 2
  • 2008 Ducati Superbike 848 | Owners Manual - Page 3
    Motor Holding S.p.a wishes you an enjoyable ride. We are continuously working to improve our Technical Assistance service. For this reason, we recommend that you follow strictly the instructions in this manual, especially those regarding the running-in period. In this way, you can be sure your
  • 2008 Ducati Superbike 848 | Owners Manual - Page 4
    Table of contents Gearchange pedal 44 Adjusting the position of the gearchange and rear brake pedals 45 Main components and devices 47 E General indications 6 Warranty 6 Symbols 6 Useful road safety information 7 Riding with a full load 8 Identification data 9 Position on motorcycle 47 Fuel tank
  • 2008 Ducati Superbike 848 | Owners Manual - Page 5
    Charging the battery 74 Checking the chain tension 75 Lubricating the drive chain 75 Changing the high and low beam bulbs 76 Changing the sidelight bulb 78 Rear turn indicators 79 Number plate light 79 Headlight aim 80 Rearview mirror adjustment 81 Tubeless tyres 82 Checking the engine oil level 84
  • 2008 Ducati Superbike 848 | Owners Manual - Page 6
    , please contact a Ducati Dealer or Authorized Service Centre. You will find the information in the manual useful on trips (which Ducati Motor Holding the warranty is automatically invalidated. Warning Failure to comply with these instructions may put you at risk, and could lead to severe injury
  • 2008 Ducati Superbike 848 | Owners Manual - Page 7
    Useful road safety information Warning Read this section before riding your motorcycle. Many accidents are the result of the inexperience of the rider. Always make sure you have your licence with you; you need a valid licence that entitles you to ride a motorcycle. Do not lend your motorcycle to
  • 2008 Ducati Superbike 848 | Owners Manual - Page 8
    Riding with a full load Your motorcycle is designed for travelling over long distances with a full load in complete safety. Even weight distribution is critical for maintaining safety standards and to avoid getting into difficulties when making sudden manoeuvres or riding on bumpy roads. E
  • 2008 Ducati Superbike 848 | Owners Manual - Page 9
    Identification data All Ducati motorcycles have two identification numbers, one for the frame (fig. 1) and one for the engine (fig. 2). Frame number Engine number E Notes These numbers indicate the motorcycle model and should be quoted when ordering spare parts. fig. 1 fig. 2 9
  • 2008 Ducati Superbike 848 | Owners Manual - Page 10
    Controls 1 4 8 7 E Warning This section shows the position and function of the controls used to drive the motorcycle. Be sure to read this information carefully before you use the controls. 3 2 6 5 9 Position of the motorcycle controls (fig. 3) 1) 2) 3) 4) 5) 6) 7) 8) 9) Instrument panel. Key-
  • 2008 Ducati Superbike 848 | Owners Manual - Page 11
    unit has found errors and has therefore blocked the engine. 9) "Motorcycle diagnostics" light. Illuminates when the motorcycle diagnostics detects a problem. 10) Rev limiter indicator lights Indicator light 10A: illuminates steadily at 800 rpm before intervention of the rev limiter. Indicator light
  • 2008 Ducati Superbike 848 | Owners Manual - Page 12
    11) Control buttons A and B. Button used for displaying and setting instrument panel parameters. It has two positions, A "▲" and B "▼". 12) High beam headlight FLASH button (fig. 5). The button that normally has the full beam flash function can be used for the LAP functions. 12 A E 11 B fig. 5
  • 2008 Ducati Superbike 848 | Owners Manual - Page 13
    LCD - Main functions Warning Any adjustments to the instrument panel must only be carried out when the motorcycle is stationary. Never operate the instrument panel controls while riding the motorcycle. 1) Speedometer. Indicates road speed 2) Odometer. Shows total distance travelled. 3) Trip meter.
  • 2008 Ducati Superbike 848 | Owners Manual - Page 14
    interval has been reached. The message is displayed only at Key-On for 5 seconds. The service indicator will be reset at a DUCATI Authorised Workshop during the service. Important E The instrument panel is part of the on-board electronic injection/ignition system diagnostics. The related menus
  • 2008 Ducati Superbike 848 | Owners Manual - Page 15
    LCD - How to set/display parameters At key-on (key turned from OFF to ON) the instrument panel activates all the digits of the LCD for 1 second and switches on the indicator lights in sequence. It then reverts to "normal" mode and, in place of motorcycle speed, shows the model and, for 2 seconds,
  • 2008 Ducati Superbike 848 | Owners Manual - Page 16
    E At Key-On, the instrument panel always shows the following information (de-activating any previously activated functions): Odometer Air temperature Clock Speed Coolant temperature Engine rpm At this point, with button (1, fig. 8) in position B "▼" it is possible to switch from the odometer
  • 2008 Ducati Superbike 848 | Owners Manual - Page 17
    Total distance travelled indicator (odometer) At Key-On the system automatically enters this function. The reading is saved permanently and cannot be reset. If it exceeds 99999 km (or 99999 miles), the reading "99999" remains displayed permanently. vs. EU vs. UK v.s. USA E fig. 9 17
  • 2008 Ducati Superbike 848 | Owners Manual - Page 18
    E Trip meter "TRIP A" While in this function, if you press button (1, fig. 8) in position B "▼" for 3 seconds, the reading is reset. If the reading exceeds 999.9, it is reset to zero and the count restarts automatically. If the system's units of measurement are changed at any time with the "Setting
  • 2008 Ducati Superbike 848 | Owners Manual - Page 19
    "TRIP FUEL" (distance travelled on reserve fuel) indicator When the fuel warning light comes on, the TRIP FUEL meter is activated automatically, regardless of the function displayed. If the fuel level remains in reserve, the reading is saved even after Key-Off. The count stops automatically when the
  • 2008 Ducati Superbike 848 | Owners Manual - Page 20
    E Coolant temperature indicator Displays the engine coolant temperature: if the reading is less than or equal to -40 °C (-40 °F), the display shows a series of flashing dashes ("---") and the Engine Diagnostics warning light comes on (8, fig. 4); if the reading is between -39 °C (-38 °F) and +39 °C
  • 2008 Ducati Superbike 848 | Owners Manual - Page 21
    indicator (SERV) Indicates that the next service is due. The message "SERV" appears on the display at the following intervals: after the first 1000 km on is displayed only at Key-On for 5 seconds. When the message appears, contact your Ducati dealer or Authorized Service Centre. E fig. 15 21
  • 2008 Ducati Superbike 848 | Owners Manual - Page 22
    E Battery voltage indicator (BATT) To display this function, go into the menu and select the "BATT" page. The battery voltage reading is displayed as follows: if the reading is between 12.1 and 14.9 Volts, it is steadily illuminated on the display; if the reading is between 10.0 and 12.0 Volts or
  • 2008 Ducati Superbike 848 | Owners Manual - Page 23
    Adjusting the engine idle speed (rpm) To display the function, go into the menu and call up the "RPM" page. In addition to the upper rev counter scale, the display also shows engine rpm numerically so that you can adjust the idle speed more precisely. E fig. 17 23
  • 2008 Ducati Superbike 848 | Owners Manual - Page 24
    E Lap time display To activate this function, go into the menu and set the "LAP" function to "On" by keeping button (1, fig. 8) in position B "▼" for 3 seconds. START and STOP the timer by pressing the high beam FLASH button (12, fig. 5) on the left-hand handlebar switch. When the LAP function is
  • 2008 Ducati Superbike 848 | Owners Manual - Page 25
    When you switch the LAP function off using the menu, the lap in progress is not saved. If the LAP function is active and the display is suddenly switched off (Key-Off), the LAP function is switched off automatically (even if the timer was ON, the lap in progress is not saved). If the timer is not
  • 2008 Ducati Superbike 848 | Owners Manual - Page 26
    E Press A LAP Memory display Displays the data saved with the LAP function: lap time, MAX speed and MAX rpm. To display the saved lap times, go into the menu and select the "LAP MEM" page. From this page, if you hold button (1, fig. 8) in position B "▼" for 3 seconds, the data for the first lap
  • 2008 Ducati Superbike 848 | Owners Manual - Page 27
    Clock setting To set the clock, select the "TIME Set" page from the menu. From this page, if you press button (1, fig. 8) in position B "▼" for 3 seconds, you enter clock setting mode. On entering this function, the message "AM" flashes on the display; if you press button (1, fig. 8) in position B
  • 2008 Ducati Superbike 848 | Owners Manual - Page 28
    Instrument panel diagnostics Warning Every time an error is displayed, always contact an authorized Ducati Service Centre. Important The instrument runs the system diagnostics correctly 60 seconds after the last Key-Off. Any errors detected in the behaviour of the motorcycle
  • 2008 Ducati Superbike 848 | Owners Manual - Page 29
    Warning light Error message INJE INJE PUMP FAN FAN STRT STRT STEP. STEP. STEP. LAMB. 13.1 13.2 16.0 18.1 18.2 19.1 19.2 21.1 21.2 21.3 22.1 Error Vertical cylinder injector error Vertical cylinder injector error Fuel pump relay error Fan relay error Fan relay error Starter contactor error Starter
  • 2008 Ducati Superbike 848 | Owners Manual - Page 30
    Warning light Error message LAMB. EXVL 22.2 23.1 23.2 23.3 23.4 23.5 1.1 1.2 2.1 2.2 3.1 Error Lambda heater error Exhaust valve motor error Exhaust valve motor error Exhaust valve motor error Exhaust valve motor error Exhaust valve motor error Throttle position sensor error Throttle position
  • 2008 Ducati Superbike 848 | Owners Manual - Page 31
    Warning light Error message T.WAT AIR AIR BATT BATT LAMB TILT 3.2 4.1 4.2 5.1 5.2 6.1 6.2 Error Engine coolant temperature sensor error Air temperature sensor error Air temperature sensor error Battery voltage error Battery voltage error Lambda sensor error Lambda 2 sensor error Traction control
  • 2008 Ducati Superbike 848 | Owners Manual - Page 32
    Warning light Error message IMMO IMMO 37.0 37.1 37.3 37.4 37.5 38.0 Error Immobilizer error Immobilizer error Immobilizer error Immobilizer error Immobilizer error CAN line error E IMMO IMMO IMMO CAN 32
  • 2008 Ducati Superbike 848 | Owners Manual - Page 33
    Display backlight The instrument panel backlight is switched on only if the parking lights or low/high beam is on. In this case the instrument panel, using sensors that measure ambient temperature and light intensity, automatically turn the backlight on or off. Intelligent headlight switch-off This
  • 2008 Ducati Superbike 848 | Owners Manual - Page 34
    (1) attached, which shows their identification number. E Notes Your Ducati dealer may ask you to produce your Code Card in order to carry out certain servicing operations. The black keys (B) are the keys for normal use, and are used to: - start the engine - open the fuel tank filler plug - open
  • 2008 Ducati Superbike 848 | Owners Manual - Page 35
    Warning Keep the keys separate, and store the tags (1) in a safe place. It is also recommended to use always the same black key to start the motorcycle. Code card A CODE CARD (fig. 23) is supplied with the keys. This shows the electronic code (A, fig. 24) that must be used if the engine is locked
  • 2008 Ducati Superbike 848 | Owners Manual - Page 36
    Immobilizer override procedure Should the immobilizer become locked, you can perform the "Immobilizer Override" procedure from the instrument panel by entering the respective function as follows: Select the "CODE" page from the menu. Notes E This menu should be active only if there is at least
  • 2008 Ducati Superbike 848 | Owners Manual - Page 37
    Entering the code: on entering this function, the first digit on the left starts flashing. Button (1, fig. 8): each time you press the button in position B "▼, the number increases cyclically in steps of one digit every second. If you press the button in position A "▲", you can set the second digit,
  • 2008 Ducati Superbike 848 | Owners Manual - Page 38
    the engine still does not start, try again with the other black key. If the engine still does not start, contact the DUCATI Service network. Duplicate keys If you need additional keys, contact your DUCATI Service Centre with all the keys you have in your possession and your CODE CARD. The Ducati
  • 2008 Ducati Superbike 848 | Owners Manual - Page 39
    Ignition switch and steering lock (fig. 26) This is located in front of the fuel tank and has four positions: A) B) C) D) ON: enables lights and engine operation; OFF: disables lights and engine operation; LOCK: the steering is locked; P: parking light on and steering locked. B A C D Notes To
  • 2008 Ducati Superbike 848 | Owners Manual - Page 40
    Left-hand handlebar switch (fig. 27) 1) Dip switch, two-position light selector switch: position = low beam headlight on; position = high beam headlight on. 2) Button = three-position turn signal: centre position = off; position = left turn; position = right turn. To cancel the indicator, press the
  • 2008 Ducati Superbike 848 | Owners Manual - Page 41
    Clutch lever The lever (1) disengages the clutch. The span adjuster (2) serves to alter the distance of the lever from the handlebar. The lever distance can be adjusted through 10 clicks of the knob (2). Turn the knob clockwise to move the lever away from twistgrip, or counter clockwise to move it
  • 2008 Ducati Superbike 848 | Owners Manual - Page 42
    Right-hand handlebar switch (fig. 29) 1) Two-position ENGINE STOP switch: position (RUN) = run; position (OFF) = stop engine. 3 1 2 Warning E This switch is mainly intended for use in emergencies when you need to stop the engine quickly. After stopping the engine, return the switch to the
  • 2008 Ducati Superbike 848 | Owners Manual - Page 43
    Front brake lever (fig. 30) Pull the lever (1) towards the twistgrip to operate the front brake. The system is hydraulically assisted and you only need to pull the lever gently. The brake lever has a knob (2) for adjusting the distance between lever and twistgrip on the handlebar. Lever distance is
  • 2008 Ducati Superbike 848 | Owners Manual - Page 44
    Rear brake pedal (fig. 31) Push down on the pedal (1) with your foot to operate the rear brake. The system is controlled hydraulically. 1 E fig. 31 Gearchange pedal (fig. 32) The gear change pedal is at rest when in centre position N, and automatically returns to the centre position. When in
  • 2008 Ducati Superbike 848 | Owners Manual - Page 45
    Adjusting the position of the gearchange and rear brake pedals (fig. 33 and fig. 34) The position of the gearchange and rear brake pedals in relation to the footrests can be adjusted to suit the requirements of the rider. To adjust the position, proceed as follows: restrain the tie-rod (1) and
  • 2008 Ducati Superbike 848 | Owners Manual - Page 46
    E To adjust the position of the rear brake pedal, proceed as follows: Loosen the locknut (4). Turn the pedal travel adjustment bolt (5) until the pedal is in the desired position. Tighten the locknut (4) to a torque of 2.3 Nm. Operate the pedal by hand to check that there is 1.5 to 2 mm of freeplay
  • 2008 Ducati Superbike 848 | Owners Manual - Page 47
    Main components and devices 9 8 E Position on motorcycle (fig. 35) 1) 2) 3) 4) 5) 6) 7) 8) 9) Fuel tank filler cap Seat lock. Side stand. Rear view mirrors. Front fork adjusters. Rear shock absorber adjusters. Suspension tie-rod for adjustment of rear ride height. Exhaust silencer (see note on
  • 2008 Ducati Superbike 848 | Owners Manual - Page 48
    Fuel tank filler cap (fig. 36) Opening Raise the cover (1) and insert the key into the lock. Give the key a 1/4 turn clockwise to unlock. Lift the cap. E Closing Close the cap with the key inserted and push it into its seat. Turn the key anticlockwise to the initial position and remove it. Replace
  • 2008 Ducati Superbike 848 | Owners Manual - Page 49
    Seat lock Opening (fig. 37) Insert the key into the seat lock (1) and turn it clockwise until the seat catch disengages with an audible click. Raise the rear of the seat (2) until it can be extracted. 0 1 0 1 1 2 E fig. 37 Closing (fig. 38) Fit the hooks on the base of the seat under the rear
  • 2008 Ducati Superbike 848 | Owners Manual - Page 50
    Before lowering the side stand, make sure that the supporting surface is hard and flat. Do not park on soft case the sidestand must be up). E Warning Do not sit on the motorcycle when it is supported on the sidestand. To move the side stand to its rest position (horizontal position), tilt the
  • 2008 Ducati Superbike 848 | Owners Manual - Page 51
    Front fork adjusters The front fork can be adjusted in rebound, compression and preload. The settings are adjusted by way of external adjuster screws: 1) to adjust rebound damping (fig. 40); 2) to adjust inner spring preload (fig. 40); 3) to adjust compression damping (fig. 41). Park the motorcycle
  • 2008 Ducati Superbike 848 | Owners Manual - Page 52
    The STANDARD factory settings are as follows: compression: 3/4 turns; rebound: 12 clicks. Spring preload (A, fig. 40): 18 mm. 3 E To change the spring preload for each fork leg, turn the adjuster (2, fig. 40) with a 22 mm hex wrench. Important Adjust both fork legs to the same setting. fig. 41
  • 2008 Ducati Superbike 848 | Owners Manual - Page 53
    Rear shock absorber adjusters (fig. 42) The shock absorber has external adjusters that enable you to adjust the suspension to suit the load on the motorcycle. Adjuster (1), located on the left-hand side at the point at which the shock absorber is fixed to the swingarm, controls rebound damping. The
  • 2008 Ducati Superbike 848 | Owners Manual - Page 54
    Once the desired spring preload has been set, re-tighten the upper lock nut. Warning E Use a pin wrench to turn the preload adjusting nut. Take special care when turning the nut, to avoid injuring your hand by striking it violently against other parts of the motorcycle if the wrench suddenly
  • 2008 Ducati Superbike 848 | Owners Manual - Page 55
    Riding the motorcycle To allow all the mechanical moving parts in the motorcycle to adapt to one another, and to avoid shortening the life of the main engine components, it is advisable to avoid sudden acceleration and running the engine at high rpm for too long, especially uphill. It is also
  • 2008 Ducati Superbike 848 | Owners Manual - Page 56
    the running-in period, be careful to stick to the recommended maintenance schedule and periodic service intervals indicated in the warranty booklet. Failure to follow these instructions releases Ducati Motor Holding S.p.A. from any liability whatsoever for any engine damage or shorter engine
  • 2008 Ducati Superbike 848 | Owners Manual - Page 57
    the correct position (page 50). Warning If there are any faults or malfunctions, do not start the motorcycle and contact your DUCATI Dealer or Authorized Service Centre. E 57
  • 2008 Ducati Superbike 848 | Owners Manual - Page 58
    Starting the engine Warning Before starting the engine, familiarise yourself with the controls that you will use when riding (page 10). B A C E Warning Never start or run the engine in an enclosed space. Exhaust gases are toxic and may lead to loss of consciousness or even death within a short
  • 2008 Ducati Superbike 848 | Owners Manual - Page 59
    2) Check that the stop switch (2, fig. 45) is positioned to (RUN), then press the starter button (3, fig. 45). Important Do not rev the engine when cold. Allow some time for the oil to warm up and reach all points that need lubricating. 2 E 3 fig. 45 59
  • 2008 Ducati Superbike 848 | Owners Manual - Page 60
    Moving off 1) Disengage the clutch by squeezing the clutch lever. 2) Push down the gearchange lever firmly with the tip of your foot to engage first gear. 3) Raise the engine revs by turning the throttle twistgrip while gradually releasing the clutch lever. The motorcycle will start moving. 4)
  • 2008 Ducati Superbike 848 | Owners Manual - Page 61
    Stopping the motorcycle Reduce speed, shift down and release the throttle twistgrip. Change down to engage first gear and then neutral. Apply the brakes and bring the motorcycle to a complete stop. Switch the engine off by turning the key to OFF (page 39). Warning Using padlocks or other locks
  • 2008 Ducati Superbike 848 | Owners Manual - Page 62
    Refuelling (fig. 46) Do not overfill the tank when refuelling. The fuel level should always be below the rim of the filler recess. Max level Warning E Use fuel with low lead content and an original octane number of 95 minimum (see table "Fluids and lubricants" on page 93). Check that no fuel is
  • 2008 Ducati Superbike 848 | Owners Manual - Page 63
    Toolkit and accessories (fig. 47) The compartment under the pillion seat contains: use and maintenance manual; helmet fastening cable; toolkit consisting of: - spark plug wrench; - Tommy bar for spark plug wrench; - double-ended screwdriver; - Allen key for fairing panels. E fig. 47 63
  • 2008 Ducati Superbike 848 | Owners Manual - Page 64
    Main Use and Maintenance Operations E Removing the fairing panels Some parts of the motorcycle fairing have to be removed for certain maintenance or repair operations. Side fairings Remove the side fairings using the Allen key located in the underseat compartment; unscrew: the two bolts (1)
  • 2008 Ducati Superbike 848 | Owners Manual - Page 65
    Notes Be careful of the splashguard, which is released by the fairing panel fastening. Notes To refit the left fairing panel, lower the sidestand and pass it through the aperture provided in the panel. 6 E fig. 49 65
  • 2008 Ducati Superbike 848 | Owners Manual - Page 66
    Rearview mirrors Unscrew the bolts (1) securing the rearview mirror. Release the pins (2) from the retaining clips (3) attached to the headlight shell bracket (4). Slip off the rubber covers (5) and disconnect the turn indicator wiring connectors (6). Repeat the procedure to remove the other
  • 2008 Ducati Superbike 848 | Owners Manual - Page 67
    shell, first remove the rearview mirrors and side fairing panels as described above. Unscrew the two rear bolts (1) securing the headlight shell to the headlight support. 1 E Notes After refitting the headlight shell, refit the side body panels and rear-view mirrors. fig. 52 67
  • 2008 Ducati Superbike 848 | Owners Manual - Page 68
    Checking and topping up the coolant (fig. 53) Check the coolant level in the expansion reservoir on the right side of the motorcycle. It should be between the two marks (1) and (2). Mark (2) indicates MAX level, and mark (1) indicates MIN level. Top up if below the MIN level. 3 2 1 MAX MIN E
  • 2008 Ducati Superbike 848 | Owners Manual - Page 69
    Checking the brake and clutch fluid level The level must not fall below the MIN mark on the corresponding reservoir (fig. 54) (the figure shows the front and rear brake fluid reservoirs). If the level drops below the limit, air can get into the circuit and make the system ineffective. Brake and
  • 2008 Ducati Superbike 848 | Owners Manual - Page 70
    Clutch system If the control lever has excessive play and the transmission snatches or jams when engaging a gear, then there is probably air in the circuit. Contact a Ducati Dealer or Authorized Workshop, who will check the system and bleed the circuit. E Warning The level of clutch fluid tends to
  • 2008 Ducati Superbike 848 | Owners Manual - Page 71
    Checking the brake pads for wear (fig. 56) The brake pads are marked with wear indicators so that they can be checked without removing them from the calipers. If the grooves in the friction material are still visible, the pad is still in good condition. MIN 1 mm Important Have the brake pads
  • 2008 Ducati Superbike 848 | Owners Manual - Page 72
    smoothly inside the outer cables: if you feel any friction or catching, have the cable replaced by a Ducati Dealer or Authorized Service Centre. To prevent problems, periodically open the twistgrip housing by unscrewing the two bolts (1, fig. 57) and lubricate the ends of each control cable and
  • 2008 Ducati Superbike 848 | Owners Manual - Page 73
    In all handlebar positions, the throttle twistgrip should have free play of 1.5 - 2.0 mm measured at the edge of the twistgrip. If necessary, adjust using the adjusters (1 and 2, fig. 59) located on the steering tube on the right-hand side of the motorcycle. Adjuster (1) is for throttle opening, and
  • 2008 Ducati Superbike 848 | Owners Manual - Page 74
    terminals, which could ignite the gases inside the cells. Always connect the red positive terminal (+) first. Replace the battery in its support (3), then connect the terminals. Apply some grease to the bolts to improve conductivity and fasten the bracket (2) with the bolt (1). 1 3 + - 2 fig
  • 2008 Ducati Superbike 848 | Owners Manual - Page 75
    Checking the chain tension (fig. 61) Important Have the chain tensioned at a Ducati Dealer or Authorized Workshop. Chain tensioning (on sidestand): position the tape measure half way along the bottom run of the chain, press the chain down and adjust the tension until the distance between the
  • 2008 Ducati Superbike 848 | Owners Manual - Page 76
    Changing the high and low beam bulbs Before replacing a burnt-out bulb, make sure that the new one matches the voltage and wattage specifications in the "Electrical System" paragraph on page 99. Always check that the new bulb works before refitting removed parts. Figure fig. 62 shows the position of
  • 2008 Ducati Superbike 848 | Owners Manual - Page 77
    Notes It is not necessary to disconnect the main wiring loom cable in order to replace the headlight bulbs. Notes Be careful to hold the new bulb at the base only. Never touch the transparent body with your fingers or it will blacken resulting in reduced bulb brilliancy. Refitting After changing
  • 2008 Ducati Superbike 848 | Owners Manual - Page 78
    Changing the sidelight bulb To access the sidelights (1), reach your hand inside the headlight support and take the bulb-holders out of their seats. Turn the bulb retaining ring (1) anti-clockwise and remove the burnt-out bulb. Renew the burnt-
  • 2008 Ducati Superbike 848 | Owners Manual - Page 79
    and turn it counter-clockwise. Push in the new bulb and turn it clockwise until it clicks into place. Refit the indicator body (2) to its support and rotate it by a quarter of a turn. 1 E 2 fig. 65 Number plate light (fig. 66) To access the number plate light bulb, unscrew the bolt (3) securing
  • 2008 Ducati Superbike 848 | Owners Manual - Page 80
    Headlight aim (fig. 67) To check the headlight aim, place the motorcycle upright with the tyres inflated to the correct pressure and one person sitting astride the motorcycle. The motorcycle should be perfectly vertical, with its longitudinal axis at right angles to a wall or screen at a distance of
  • 2008 Ducati Superbike 848 | Owners Manual - Page 81
    to raise it. Repeat the above procedure to adjust the right-hand headlamp. 1 2 E fig. 68 Rearview mirror adjustment (fig. 69) The rearview mirror is adjusted manually by applying pressure at point (A). A fig. 69 81
  • 2008 Ducati Superbike 848 | Owners Manual - Page 82
    bumpy roads. Important Do not remove or alter the position of the wheel balancing weights. Notes If tyres need changing, contact a Ducati Dealer or Authorized Service Centre to make sure wheels are removed and refitted correctly. 82
  • 2008 Ducati Superbike 848 | Owners Manual - Page 83
    Minimum tread depth Measure the tread depth (S, fig. 70) at the point where the tread is most worn. It should not be less than 2 mm, and in any case not less than the legal limit. S Important Visually inspect the tyres at regular intervals for cracks and cuts, especially on the side walls, and
  • 2008 Ducati Superbike 848 | Owners Manual - Page 84
    To change the engine oil and filters at the intervals specified in the maintenance table in the Warranty Booklet, contact a Ducati dealer or Authorized Service Centre. Oil viscosity SAE 10W-40 The other viscosity degrees indicated in the table can be used if the local average temperature is within
  • 2008 Ducati Superbike 848 | Owners Manual - Page 85
    (fig. 72) Spark plugs are an important part of the engine and should be checked at regular intervals. The condition of the spark plugs provides a good indication of how well the engine is running. Have the spark plugs inspected or replaced at a Ducati Dealer or Authorized Workshop. Firstly, they
  • 2008 Ducati Superbike 848 | Owners Manual - Page 86
    General cleaning To preserve the original shine on metal surfaces and paintwork, wash and clean your motorcycle at regular intervals depending on the type of use and according to the particular road conditions. Use specific products, where possible biodegradable. Avoid aggressive detergents or
  • 2008 Ducati Superbike 848 | Owners Manual - Page 87
    Storing the motorcycle If the motorcycle is to be left unused for a long period, it is advisable to carry out the following operations first: clean the motorcycle; drain the fuel from fuel tank; pour a few drops of engine oil into the cylinders through the spark plug bores, then turn the engine over
  • 2008 Ducati Superbike 848 | Owners Manual - Page 88
    Maintenance E Programmed maintenance plan: operations to be carried out by the dealer km x1000 List of operations with frequency (distance or time interval*) Change the engine oil Change the engine oil filter Clean the engine oil pick-up filter Check the engine oil pressure Check/adjust the valve
  • 2008 Ducati Superbike 848 | Owners Manual - Page 89
    km x1000 List of operations with frequency (distance or time interval*) Check throttle body synchronisation and idle speed setting (1) Check the brake and clutch fluid levels Change the clutch and brake fluid Check and adjust the brake and clutch control cables Check/lubricate the throttle/choke
  • 2008 Ducati Superbike 848 | Owners Manual - Page 90
    Check the front sprocket retaining bolts General lubrication and greasing Check and recharge the battery Road test the motorcycle General cleaning • * Service operation to be carried out in accordance with the specified distance or time intervals (km, miles or months), whichever occurs
  • 2008 Ducati Superbike 848 | Owners Manual - Page 91
    tyre pressure and wear Check the drive chain tension and lubrication Check the brake pads. If necessary, contact your dealer to renew pads * Service operation to be carried out in accordance with the specified distance or time intervals (km, miles or months), whichever occurs first. miles x1000
  • 2008 Ducati Superbike 848 | Owners Manual - Page 92
    Technical data Overall dimensions (mm) (fig. 73) Weights In running order without liquids and battery: 169 kg. Fully laden: 390 kg. Warning Failure to observe weight limits could result in poor handling and impair the performance of your motorcycle, and could result in loss of control. E In
  • 2008 Ducati Superbike 848 | Owners Manual - Page 93
    Fluids and lubricants Fuel tank, including a reserve of 4 dm3 (litres) Lubrication circuit Front/rear brake and clutch circuits Protection for electrical contacts Front fork Cooling system Type Unleaded fuel with 95 fuel octane rating (at least) SHELL - Advance Ultra 4 Special hydraulic system
  • 2008 Ducati Superbike 848 | Owners Manual - Page 94
    . E Performance data Maximum speed in any gear should be reached only after the correct running-in period with the motorcycle properly serviced at the recommended intervals. Important Do not exceed the specified rpm limits in any running conditions. 6 2 1 Timing system Desmodromic with four
  • 2008 Ducati Superbike 848 | Owners Manual - Page 95
    Spark plugs Make: NGK. Type: MAR10A-J. Fuel system MARELLI indirect electronic injection Diameter of throttle body with oval section: 56 mm. Injectors per cylinder: 1. Holes per injector: 12. Fuel supply: 95-98 RON. Disc diameter: 320 mm. Hydraulically operated by a control lever on right
  • 2008 Ducati Superbike 848 | Owners Manual - Page 96
    Warning The brake fluid used in the brake system is corrosive. In the event of accidental contact with eyes or skin, wash the affected area with copious amounts of running water. Transmission E Dry clutch operated by a control lever on left handlebar. Transmission from engine to gearbox main
  • 2008 Ducati Superbike 848 | Owners Manual - Page 97
    Frame ALS 450 steel tube trellis frame. ALS 450 steel tube trellis rear subframe Steering angle (on each side): 28° 30'. Steering head angle: 24° 30'. Trail: 97 mm. Tyres Front Radial tubeless tyre Size: 120/70-ZR17 Rear Radial tubeless tyre Size: 180/55-ZR17 E Wheels Five-Y-spoke, light-alloy
  • 2008 Ducati Superbike 848 | Owners Manual - Page 98
    Suspension Front Hydraulic upside-down fork provided with outer adjuster for rebound, compression, and preload (for inner springs of fork legs). Stanchion diameter: 43 mm. Travel along leg axis: 127 mm. Rear Progressive linkage with a rocker arm connecting the frame and upper pivot point of the
  • 2008 Ducati Superbike 848 | Owners Manual - Page 99
    that specified. Failure to observe this rule may damage the electric system or even cause fire. Notes See "Replacing bulbs" on page 76 for relevant instructions. 99
  • 2008 Ducati Superbike 848 | Owners Manual - Page 100
    3 3 E 1 IN GOOD CONDITION BLOWN fig. 75 fig. 77 2 fig. 76 100
  • 2008 Ducati Superbike 848 | Owners Manual - Page 101
    Key to the electrical system / injection system diagram 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) 15) 16) 17) 18) 19) 20) 21) 22) 23) 24) 25) 26) 27) 28) 29) Right-hand handlebar switch Key switch Left cooling fan Right cooling fan Starter motor Starter contactor Battery Regulator fuse
  • 2008 Ducati Superbike 848 | Owners Manual - Page 102
    Injection Engine Electronic Control Unit Fans Val. 10 A 15 A 15 A 5A 20 A 5A 7,5 A Notes The electrical system wiring diagram is at the end of this manual. 102
  • 2008 Ducati Superbike 848 | Owners Manual - Page 103
    Periodic maintenance record km 1000 12000 24000 36000 48000 60000 Name of Ducati Service Mileage Date E 103
  • 2008 Ducati Superbike 848 | Owners Manual - Page 104
    E 104
  • 2008 Ducati Superbike 848 | Owners Manual - Page 105
    it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Ducati North America. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424
  • 2008 Ducati Superbike 848 | Owners Manual - Page 106
    if the motorcycle noise has increased significantly through use. Otherwise, the owner may become subject to penalties under state and local ordinances. Problems that may affect motorcycle emissions If you are aware of any of the following symptoms, have the vehicle inspected and repaired by your
  • 2008 Ducati Superbike 848 | Owners Manual - Page 107
    explosive under certain conditions. Refuell in a well ventilated area with the engine stopped. Do not smoke or allow open flames or sparks when refuelling or servicing the fuel system. 107
  • 2008 Ducati Superbike 848 | Owners Manual - Page 108
    Always close the fuel petcock when the engine is not running to prevent flooding of the throttle body. Do not overfill fuel tank (see instructions page 55). Motorcycle exhaust contains poisonous carbon monoxide gas. Do not inhale exhaust gases and never run the engine in a closed garage or confined
  • 2008 Ducati Superbike 848 | Owners Manual - Page 109
    Label location (fig. B) 1 2 8 2 only Canada 5 E USA fig. B 4 7 6 3 109
  • 2008 Ducati Superbike 848 | Owners Manual - Page 110
    1 E USA 2 31 ÷ 33 mm 2 (Only Canada) 3 4 5 6 7 8 110
  • 2008 Ducati Superbike 848 | Owners Manual - Page 111
    of initial retail delivery, whichever first occurs. E USA Important In the event of fuel system malfunction, contact Ducati's authorized Service Centres. 6 4 3 CANISTER I. Coverage Warranty defects shall be remedied during customary business hours at any authorized Ducati motorcycle dealer
  • 2008 Ducati Superbike 848 | Owners Manual - Page 112
    which adversely affect performance and/or (5) use in competitive racing or related events. B. Inspections, replacement of parts and other services and adjustments required for routine maintenance. C. Any motorcycle on which odometer mileage has been changed so that actual mileage cannot be
  • 2008 Ducati Superbike 848 | Owners Manual - Page 113
    not liable for these parts. The owner is responsible for the performance of all required maintenance. Such maintenance may be performed at a service establishment or by any individual. The warranty period begins on the date the motorcycle is delivered to an ultimate purchaser. Ducati North America
  • 2008 Ducati Superbike 848 | Owners Manual - Page 114
    Routine maintenance record Km 1,000 mi 600 7,500 15,000 22,500 30,000 37,500 Ducati Service Name Mileage Date E USA 12,000 24,000 36,000 48,000 60,000 114
  • 2008 Ducati Superbike 848 | Owners Manual - Page 115
    Stampato 09/2007 Cod. 913.7.120.1A Ducati Motor Holding spa via Cavalieri Ducati, 3 40132 Bologna, Italia Tel. +39 051 6413111 Fax +39 051 406580 www.ducati.com
  • 2008 Ducati Superbike 848 | Owners Manual - Page 116
    42 Gr/Bk W/P W/Bk W/V W/G O/Bk O/W AIR BODY 1 BODY 4 BODY 6 BODY 7 Bk/B G/W O/W R/Bk BODY 11 BODY 14 BODY 16 BODY 17 BODY 20 BODY 22 BODY 24 BODY 27 W/B Gr/G BODY 28 BODY 29 BODY 32 BODY 33 BODY 38 ENGINE 3 ENGINE 5 W Gr/G ENGINE 9 ENGINE 10 ENGINE 13 ENGINE 14 ENGINE 17 ENGINE 18 Bk Lb Gr V
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
1
E
Use and maintenance manual
848