Rane MP2015 Owners Manual - Page 9

Deck Input Channels Source Selectors The source selectors choose the active USB port, USB audio slot or analog input for each input channel. To use USB playback you must assign the USB slots in your DJ or DAW software preferences panel. Deck 1 Source Selections Deck 2 Source Selections Deck 3 Source Selections Deck 4 Source Selections Port A playback for Deck 1 • USB audio slots 1-2. • Routes audio and MIDI for Deck 1 only to/from USB Port A. • Phono / CD 1 • Set the PH-CD-SP switch on the rear panel. Port A playback for Deck 2 • USB audio slots 3-4. • Routes audio and MIDI for Deck 2 only to/from USB Port A. Port A playback for Deck 3 • USB audio slots 5-6. • Routes audio and MIDI for Deck 3 only to/from USB Port A. • Phono / CD 2 • Phono / CD 3 • Set the PH-CD-SP switch • Set the PH-CD-SP switch on the rear panel. on the rear panel. • Aux Input (common to all selectors). Port A playback for Deck 4 • USB audio slots 7-8. • Routes audio and MIDI for Deck 4 only to/from USB Port A. • Phono / CD 4 • Set the PH-CD-SP switch on the rear panel. Port B playback for Deck 1 • USB audio slots 1-2. • Routes audio and MIDI for Deck 1 only to/from USB Port B. Port B playback for Deck 2 • USB audio slots 3-4. • Routes audio and MIDI for Deck 2 only to/from USB Port B. Port B playback for Deck 3 • USB audio slots 5-6. • Routes audio and MIDI for Deck 3 only to/from USB Port B. Port B playback for Deck 4 • USB audio slots 7-8. • Routes audio and MIDI for Deck 4 only to/from USB Port B. For details on sharing the MP2015 with a second computer, see "DJ Changeover" on page 15. Deck Source Selection is followed by: • GAIN trim • Off to +15 dB with unity gain at 12 o'clock. • 3-band HIGH / MID / LOW tone controls • Off to +6 dB with unity gain at 12 o'clock. • Linkwitz-Riley 2nd-order isolator full-cut filters (LR-2). • Crossover points for Low/Mid and Mid/High default at 300 Hz between Low and Mid, 3 kHz between Mid and High. This can be changed for each Deck. See "Control Panel" on page 16. • High-Pass / Low-High-Pass / Low-Pass Sweep FILTER • LP: Low-pass filter cutoff moves from 20 kHz toward 20 Hz as the knob is turned CCW. • HP: High-pass filter cutoff moves from 20 Hz toward 20 kHz as the knob is turned CW. • L-H: In Low-High mode, there is no effect at the center (flat response). • Low-pass increases CCW from the center. • High-pass increases CW from the center. • Resonance can be adjusted for all Sweep Filters with the RESONANCE control. • CUE select • Assigns a Deck to the headphone monitor. • Q-peak meter with peak hold • Adjust the GAIN trim to get the signal into the yellow during peaks, and to prevent overload. • MIX control • Adjusts the channel level feeding the USB record outputs, Submix or Main mix. • Submix • When the SUB button (next to the Source selector) is pressed and lit blue, the Deck is sent to the Submix. When this button is off, the channel is sent to the Main Mix. See "Submix" on page 10. See "Main Mix Outputs" on page 13. PH/CD 1 AUX 1A 1B SOURCE I 456 3 7 SUB 2 8 1 9 0 10 GAIN | OL +10 OFF +6 +7 HIGH +5 +3 | +2 +1 0 -1 OFF +6 -2 MID -3 -5 | -7 -10 -15 -24 OFF +6 LOW FILTER 456 3 7 2 8 1 0 MIX 9 10 CUE I MP2015 MANUAL 9