Panasonic AJ-PX380GF Operating Instructions - Page 150
The [TYPE B] factory setting corresponds to the Anton/Bauer DIONIC HC.
View all Panasonic AJ-PX380GF manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 150 highlights
Chapter 6 Menu Operations - Menu list Item Description of settings [HYTRON140 NEAR END] Selects the near end voltage in steps of 0.1 V when [HYTRON140] is selected in the main menu → [BATTERY SETUP] → [BATTERY SELECT]. This item is enabled when [BATTERY MODE] is set to [MANUAL]. [12.0V]...[15.0V] ffFactory setting: [13.1V] [DIONIC HC NEAR END] Selects the near end voltage in steps of 0.1 V when [DIONIC HC] is selected in the main menu → [BATTERY SETUP] → [BATTERY SELECT]. This item is enabled when [BATTERY MODE] is set to [MANUAL]. [12.0V]...[15.0V] ffFactory setting: [13.4V] [ENDURA10 NEAR END] Selects the near end voltage in steps of 0.1 V when [ENDURA10] is selected in the main menu → [BATTERY SETUP] → [BATTERY SELECT]. This item is enabled when [BATTERY MODE] is set to [MANUAL]. [12.0V]...[15.0V] ffFactory setting: [13.4V] [PAG L96e NEAR END] Selects the near end voltage in steps of 0.1 V when [PAG L96e] is selected in the main menu → [BATTERY SETUP] → [BATTERY SELECT]. This item is enabled when [BATTERY MODE] is set to [MANUAL]. [12.0V]...[15.0V] ffFactory setting: [12.7V] [TYPE A FULL] Selects the voltage for full display in steps of 0.1 V when [TYPE A] is selected in the main menu → [BATTERY SETUP] → [BATTERY SELECT]. The [TYPE A] factory setting corresponds to the IDX ENDURA ELETE. [13.0V]...[17.0V] ffFactory setting: [15.6V] [TYPE A NEAR END] Selects the near end voltage in steps of 0.1 V when [TYPE A] is selected in the main menu → [BATTERY SETUP] → [BATTERY SELECT]. The [TYPE A] factory setting corresponds to the IDX ENDURA ELETE. [11.0V]...[15.0V] ffFactory setting: [13.2V] [TYPE A END] Selects the end voltage in steps of 0.1 V when [TYPE A] is selected in the main menu → [BATTERY SETUP] → [BATTERY SELECT]. The [TYPE A] factory setting corresponds to the IDX ENDURA ELETE. [11.0V]...[15.0V] ffFactory setting: [12.5V] [TYPE B FULL] Selects the voltage for full display in steps of 0.1 V when [TYPE B] is selected in the main menu → [BATTERY SETUP] → [BATTERY SELECT]. The [TYPE B] factory setting corresponds to the Anton/Bauer DIONIC HC. [13.0V]...[17.0V] ffFactory setting: [15.9V] [TYPE B NEAR END] Selects the near end voltage in steps of 0.1 V when [TYPE B] is selected in the main menu → [BATTERY SETUP] → [BATTERY SELECT]. The [TYPE B] factory setting corresponds to the Anton/Bauer DIONIC HC. [11.0V]...[15.0V] ffFactory setting: [12.9V] [TYPE B END] Selects the end voltage in steps of 0.1 V when [TYPE B] is selected in the main menu → [BATTERY SETUP] → [BATTERY SELECT]. The [TYPE B] factory setting corresponds to the Anton/Bauer DIONIC HC. [11.0V]...[15.0V] ffFactory setting: [12.5V] [TYPE C FULL] Selects the voltage for full display in steps of 0.1 V when [TYPE C] is selected in the main menu → [BATTERY SETUP] → [BATTERY SELECT]. [13.0V]...[17.0V] ffFactory setting: [15.9V] [TYPE C NEAR END] Selects the near end voltage in steps of 0.1 V when [TYPE C] is selected in the main menu → [BATTERY SETUP] → [BATTERY SELECT]. [11.0V]...[15.0V] ffFactory setting: [13.2V] [TYPE C END] Selects the end voltage in steps of 0.1 V when [TYPE C] is selected in the main menu → [BATTERY SETUP] → [BATTERY SELECT]. [11.0V]...[15.0V] ffFactory setting: [12.5V] [BATT STAT NEAR END] Selects the near end percent value. When the battery charge level percentage cannot be detected, this will follow the near end voltage value set for [TYPE A]. [4%], [5%], [6%], [7%], [8%], [9%], [10%], [12%], [14%], [16%], [18%], [20%] ffFactory setting: [5%] If a battery whose remaining charge is displayed in units of 10% is used, the setting value and actual near end warning may vary slightly. [BATT STAT END] Selects the end percent value. When the battery charge level percentage cannot be detected, this will follow the end voltage value set for [TYPE A]. [1%]...[10%] ffFactory setting: [1%] When using a battery which displays battery charge level by units of 10%, an end is determined only in two stages: when it is set between [1%] and [5%], or when it is set between [6%] and [10%]. - 150 -