Netgear XCM89UP Software Setup Manual Software Version 11.x - Page 10

Config#interface VLAN 1, Config#ip default-gateway <gateway-addr&gt

Get Netgear XCM89UP PDF manuals and user guides View all Netgear XCM89UP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

M6100, M5300, and M7100 Series Switches The default admin user name is admin and the default admin password is blank, that is, do not enter a password. 3. Disable the default DHCP client mode to assign an IP address manually. Enter one of the following commands: • For the management VLAN interface: (Management Switch) #config (Management Switch) (Config)#interface VLAN 1 (Management Switch) (Interface vlan 1)#no ip address dhcp • For the service port: serviceport protocol none 4. Set the IP address, subnet mask, and gateway address by entering one of the following commands: • For the management interface: a. Set the IP address:. (Management Switch) # (Management Switch) #config (Management Switch) (Config)#interface VLAN 1 (Management Switch) (Interface vlan 1)#ip address ipaddress subnetmask Note: By default, VLAN 1 is the management VLAN. b. Set the gateway: (Management Switch) (Config)#ip default-gateway • For the service port: serviceport parms ipaddress subnetmask [gateway] Use the following information to configure the parameters: • ip address. The unique IP address for the switch. Each IP parameter is made up of four decimal numbers, ranging from 0 to 255. • subnetmask. The subnet mask for the LAN. • gateway. The gateway address for the subnet. No default subnet exists. 5. To enable these changes to be retained during a reset of the switch, type save at the main menu prompt, and type y to confirm the changes. 6. To view the changes and verify the IP address information, enter the show ip interface vlan or show serviceport command. The switch is now ready for Telnet and SSH access as well as for web-based management. Get Started 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
Get Started
10
M6100, M5300, and M7100 Series Switches
The default admin user name is
admin
and the default admin password is blank, that is,
do not enter a password.
3.
Disable the default DHCP client mode to assign an IP address manually. Enter one of the
following commands:
•
For the management VLAN interface:
(Management Switch)
#config
(Management Switch)
(Config)#interface VLAN 1
(Management Switch)
(Interface vlan 1)#no ip address dhcp
•
For the service port:
serviceport protocol none
4.
Set the IP address, subnet mask, and gateway address by entering one of the following
commands:
•
For the management interface:
a.
Set the IP address:.
(Management Switch)
#
(Management Switch)
#config
(Management Switch)
(Config)#interface VLAN 1
(Management Switch)
(Interface vlan 1)#ip address
ipaddress
subnetmask
Note:
By default, VLAN 1 is the management VLAN.
b.
Set the gateway:
(Management Switch)
(Config)#ip default-gateway <gateway-addr>
•
For the service port:
serviceport parms
ipaddress
subnetmask
[
gateway
]
Use the following information to configure the parameters:
•
ip address
. The unique IP address for the switch. Each IP parameter is made up of
four decimal numbers, ranging from 0 to 255.
•
subnetmask
. The subnet mask for the LAN.
•
gateway
. The gateway address for the subnet. No default subnet exists.
5.
To enable these changes to be retained during a reset of the switch, type
save
at the main
menu prompt, and type
y
to confirm the changes.
6.
To view the changes and verify the IP address information, enter the
show ip interface
vlan <management vlan ID>
or
show serviceport
command.
The switch is now ready for Telnet and SSH access as well as for web-based
management.