Kenwood TM-V708A User Manual - Page 62

Dcs Code Id

Get Kenwood TM-V708A PDF manuals and user guides View all Kenwood TM-V708A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

DCS CODE ID This function scans through all DCS codes to identify the incoming DCS code on a received signal. You may find this useful when you cannot recall the DCS code that the other persons in your group are using. 1 Press [TONE] to switch the DCS function ON. • "DCS" appears when the DCS function is ON. 2 Press [F], [T.SEL]. • The current DCS code appears and blinks. 3 Press [SCAN] to activate the DCS Code ID. • "DCS SCAN" appears and blinks. 4 Press [OK] to program the identified code in place of the currently set code. • The DCS function will remain ON. You can press [TONE] to switch the DCS function OFF. • Press [ESC] if you do not want to program the identified code. • Press [SCAN] while the identified code is blinking, to resume scanning. Note: Received signals are audible while scanning is in progress. 11 • Scan starts when signals are received. • To reverse the scan direction, turn the Tuning control clockwise (upward scan) or counterclockwise (downward scan). You can also press Mic [UP]/ [DWN]. • To end this function, press [ESC]. • When the DCS code is identified, the identified code appears and blinks. 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
56
11
4
Press
[OK]
to program the identified code in place of
the currently set code.
°
The DCS function will remain ON.
You can press
[TONE]
to switch the DCS function OFF.
°
Press
[ESC]
if you do not want to program the identified
code.
°
Press
[SCAN]
while the identified code is blinking, to
resume scanning.
Note
:
Received signals are audible while scanning is in progress.
DCS CODE ID
This function scans through all DCS codes to identify the
incoming DCS code on a received signal.
You may find
this useful when you cannot recall the DCS code that the
other persons in your group are using.
1
Press
[TONE]
to switch the DCS function ON.
°
±DCS² appears when the DCS function is ON.
2
Press
[F]
,
[T.SEL]
.
°
The current DCS code appears and blinks.
3
Press
[SCAN]
to activate the DCS Code ID.
°
±DCS SCAN² appears and blinks.
°
Scan starts when signals are received.
°
To reverse the scan direction, turn the
Tuning
control
clockwise (upward scan) or counterclockwise
(downward scan).
You can also press Mic
[UP]
/
[DWN]
.
°
To end this function, press
[ESC]
.
°
When the DCS code is identified, the identified code
appears and blinks.