Invacare ORBITB Owners Manual - Page 63

Replacing Handrims

Get Invacare ORBITB PDF manuals and user guides View all Invacare ORBITB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Replacing Handrims SECTION 9-REAR WHEELS Non-Projection Handrims NOTE: For this procedure, refer to FIGURE 9.3. NOTE: The following procedures will work for any type of projection handrim. Removing Non-Projection Handrims 1. Remove rear wheel from the wheelchair. Refer to Removing/Installing Rear Wheels on page 61. 2. Remove the button screws that secure the handrim to the rear wheel and remove handrim. Installing Non-Projection Handrims NOTE: For this procedure, refer to 1. Install the new handrim onto rear wheel. 2. Secure handrim to rear wheel with button screws. ƽ WARNING Make sure detent pin and locking pins of the quick-release axles are fully released before operating the wheelchair. 3. Reinstall rear wheel onto the wheelchair. Refer to Removing/Installing Rear Wheels on page 61. 4. If the locking pins of the quick‐release axles are not protruding past the inside of the axle bushing or there is too much movement of the rear wheel assembly in a back and forth position, refer to Adjusting the Quick‐Release Axle on page 62. 5. Repeat procedure for opposite rear wheel, if necessary. Handrim Button Screw Composite Rear Wheels FIGURE 9.3 Replacing Handrims - Non-Projection Handrims Projection Handrims NOTE: For this procedure, refer to FIGURE 9.4 on page 64. NOTE: The following procedures will work for any type of projection handrim. Part No. 1073955 63 Orbit™

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
SECTION 9—REAR WHEELS
Part No. 1073955
63
Orbit
™
Replacing Handrims
Non-Projection Handrims
NOTE: For this procedure, refer to FIGURE 9.3.
NOTE: The following procedures will work for any type of projection handrim.
Removing Non-Projection Handrims
1.
Remove rear wheel from the wheelchair. Refer to Removing/Installing Rear Wheels
on
page 61.
2.
Remove the button screws that secure the handrim to the rear wheel and remove
handrim.
Installing Non-Projection Handrims
NOTE: For this procedure, refer to
1.
Install the new handrim onto rear wheel.
2.
Secure handrim to rear wheel with button screws.
±
WARNING
Make sure detent pin and locking pins of the quick-release axles are fully released
before operating the wheelchair.
3.
Reinstall rear wheel onto the wheelchair. Refer to Removing/Installing Rear Wheels
on page 61.
4.
If the locking pins of the quick
‐
release axles are not protruding past the inside of the
axle bushing or there is too much movement of the rear wheel assembly in a back and
forth position, refer to Adjusting the Quick
‐
Release Axle
on page 62.
5.
Repeat procedure for opposite rear wheel, if necessary.
FIGURE 9.3
Replacing Handrims - Non-Projection Handrims
Projection Handrims
NOTE: For this procedure, refer to FIGURE 9.4 on page 64.
NOTE: The following procedures will work for any type of projection handrim.
Handrim
Composite Rear
Wheels
Button
Screw