Harman Kardon AVR 135 Owners Manual - Page 20
Output Level Adjustment - 6 1 channel receiver
View all Harman Kardon AVR 135 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 20 highlights
SYSTEM CONFIGURATION ence through the use of the delay settings to adjust the timing for the speaker placement and acoustic conditions in your listening room or home theater. The AVR 135's advanced software enables you to quickly and easily set delay times without the need to calculate them using a complex formula. Instead, all you need to do is measure the approximate distance between your listening position and each of the speakers in your system. When you enter those distances into the AVR's memory as shown below, the AVR's microprocessor does the rest of the work, calculating the proper delay time. The measurements need not be accurate to the inch, as the system is designed to accommodate a typical listening area rather than require the precise measurement to one "sweet spot" position. Due to the differences in the way each surround mode operates, some modes allow for a greater range of delay times than others. To avoid problems, we recommend that delay times be adjusted using the Dolby Digital mode. If a different mode is selected at a later time, the AVR 135 will automatically restrict the delay settings to those required by the surround mode in use. Delay times are only adjustable for the Dolby modes, so you will notice that the DELAY menu may not be accessed when any other mode, such as a DTS or Logic 7 option, has been selected. In addition, when a non-Dolby Digital mode such as Dolby 3 Stereo or Pro Logic II is selected, adjustments may be made to the Surround speakers only. To set the delay time for a specific input, the DELAY ADJUST menu (Figure 7) should be visible on your on-screen display. If it is not, press the OSD Button v to bring up the MASTER MENU, and press the ¤ Button n until the on-screen › cursor is pointing at the DELAY ADJUST line. Press the Set Button p to call up the menu. NOTE: In order to adjust the Delay settings for the surround back channels, a Dolby Digital or DTS source must be playing. This enables the system to activate the surround back processing mode. * DELAY ADJUST * FRONT CENTER SURROUND SURR BACK UNIT :10FT :10FT :10FT :10FT :FEET BACK TO MASTER MENU Figure 7 Once the DELAY ADJUST menu is on your screen, note that the default setting to enter the distances from the speakers to the listening position is in feet. If your measurements are in feet, proceed to the next step; if your measurements are made in meters, press the ¤ Button n until the on-screen › cursor is at the UNIT line on the menu. Then, press the ‹/› Buttons o so that METER is highlighted. When the change in measurement units is made, press the ⁄/¤ Buttons n to return the › cursor to the CENTER position. With the on-screen › cursor pointing to CENTER, press the ‹/› Buttons o until the distance from the center speaker to the preferred listening position is entered. Next, press the ¤ Button n to move the cursor to the SURROUND line and use the ‹/› Buttons o again to enter the distance from the video display at the front of the room to the surround speakers. Finally, if the system is configured for 7.1 operation by entering LARGE or SMALL on the SURR BACK line of the SPEAKER SETUP menu, press the ¤ Button n again and use the ‹/› Buttons o to enter the distance from the listening position to the surround speakers. Remember that this last adjustment will only be needed when you have surround back speakers installed and Dolby Digital chosen as the surround mode. IMPORTANT NOTES: • Listeners are often confused about the operation of the surround channels. While some assume that sound should always be coming from each speaker, most of the time there will be little or no sound in the surround channels. This is because they are only used when a movie director or sound mixer specifically places sound there to create ambience or a special effect, or to continue action from the front of the room to the rear. Once the output levels are properly set, it is normal for surround speakers to operate only occasionally. Artificially increasing the volume to the rear speakers may destroy the illusion of an enveloping sound field that duplicates the way you hear sound in a movie theater or concert hall. • When the AVR 135 is configured for 6.1-channel operation using a single surround back speaker, the output level adjustments will still provide an adjustment for separate surround back left and surround back right positions even though your system has only one surround back speaker. This means that the Surround Back channel will seem to appear twice, and in 6.1 operation this is normal. The separate SBL/SBR adjustments for 6.1 operation are needed to optimize the balance between the two discrete channels within the AVR as they are mixed for output to a single speaker. When the speaker-to-listening-position distance has been entered for all active speaker positions, press the ⁄/¤ Buttons n until the on-screen cursor is next to BACK TO MASTER MENU and press the Set Button p. The delay settin4gs9ma4y 7be c4h5ange4d3at any time directly from the4r8emo4te6con4tro4l by4p2ressing the Delay Button 35 . C3E7NT3E9 R 4D1ELAY will appear in the Lo3w4er D3i6spla3y8Line4¯ 0 , bu3t 7you 41 47 may press the of the speaker ⁄ g3ro3/¤ upsB.2u6tton2s5n3t7o 32 27 24 36 selec3t 6any 35 40 39 46 45 Press the Set B3u1tton 2p8 w2h3en t3he5desire3d4spe3ak8er 44 group appears, a3n0d the2n9pre2ss2the 3⁄4/¤ Bu3t3tons 43 n again to en2te9r the3d0istan2c1e fro3m3the s3pe2aker to 42 the listening pos2iti8on. P3re1ss t2he0Se3t 2Button3p 1 again to enter the data. You may then press the ⁄/¤ Buttons n to select another speaker group to repeat the procedure as needed, or wait five seconds for the system to return to normal operation. Output Level Adjustment Output level adjustment is a key part of the configuration of any surround sound product. It is particularly important for a digital receiver such as the AVR 135, as correct outputs ensure that you hear soundtracks with the proper directionality and intensity. Before beginning the output level adjustment process, make certain that all speaker connections have been properly made. The system volume should be set to the level that you will use during a typical listening session. Using the Full-OSD System Follow these steps while seated in the listening position that will be used most often: 51 1. Make certain that all speaker positions have been 50 properly configured for their "large" or "small" set49 tings (as outlined above) and turn off the OSD 48 system if it is in use. 2. Adjust the volume so that it is at -15dB, as shown in the on-screen display or Lower Display Line ¯. 3. Output level adjustment is most easily done through the CHANNEL ADJUST menu (Figure 8). If you are already at the MASTER MENU, press the ¤ Button n until the on-screen › cursor is next to the CHANNEL ADJUST line. If you are not at the MASTER MENU, press the OSD Button v to bring up the MASTER MENU (Figure 1), and then press the ¤ Button n until the on-screen › cursor is next to the CHANNEL ADJUST line. Press the Set 20 SYSTEM CONFIGURATION