Epson ExpressStation User Manual - Page 42

Main System Board Jumpers

Get Epson ExpressStation PDF manuals and user guides View all Epson ExpressStation manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Main System Board Jumpers The computer contains four blocks (groups) of jumpers: J3, J5, J19, and J21. To access jumper blocks J19 and J21, you must remove any option cards that are installed. You must remove the drive housing to access jumper blocks J3 and J5. See the previous page to locate the jumper blocks on your main system board. Then follow the instructions below to change the necessary jumper settings. Caution Do not install or remove any option cards when the drive housing is removed from the computer. The housing stabilizes the option card riser board and you could severely damage it if you put stress on it without the support of the drive housing. Also, do not change the settings in the reserved jumper block J10; these jumpers must remain at their factory settings. 1 3 5 7 9 11 13 Installing and Removing Options 3-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Main System Board Jumpers
The computer contains four blocks (groups) of jumpers: J3, J5,
J19, and J21. To access jumper blocks J19 and J21, you must
remove any option cards that are installed. You must remove
the drive housing to access jumper blocks J3 and J5.
See the previous page to locate the jumper blocks on your main
system board. Then follow the instructions below to change the
necessary jumper settings.
Caution
Do not install or remove any option cards when the drive
housing is removed from the computer. The housing
stabilizes the option card riser board and you could severely
damage it if you put stress on it without the support of the
drive housing. Also, do not change the settings in the
reserved jumper block J10; these jumpers must remain at
their factory settings.
1
3
5
7
9
11
13
Installing and Removing
Options
3-3