Epic Fitness El 1200 Pro Elliptical English Manual - Page 20

Maintenance And Troubleshooting

Get Epic Fitness El 1200 Pro Elliptical PDF manuals and user guides View all Epic Fitness El 1200 Pro Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

MAINTENANCE AND TROUBLESHOOTING Inspect and tighten all parts of the elliptical exerciser regularly. Replace any worn parts immediately. To clean the elliptical exerciser, use a damp cloth and a small amount of mild soap. Important: To avoid damage to the console, keep liquids away from the console and keep the console out of direct sunlight. HANDGRIP PULSE SENSOR TROUBLESHOOTING • Avoid moving your hands while using the handgrip pulse sensor. Excessive movement may interfere with heart rate readings. • Do not hold the metal contacts too tightly; doing so may interfere with heart rate readings. • For the most accurate heart rate reading, hold the metal contacts for at least 15 seconds. • For optimal performance of the handgrip pulse sensor, keep the metal contacts clean. The contacts can be cleaned with a soft cloth-never use alcohol, abrasives, or chemicals to clean the contacts. HOW TO CALIBRATE THE RAMP If the ramp is not functioning properly, the ramp may need to be calibrated. To calibrate the ramp, hold down the Start button and the Resistance increase button for about 5 seconds until the display on the console changes. Next, press the Start button once, and then press the Ramp increase button. Then, two dashes and the word RAMP will appear in the display. The ramp is now calibrated. HOW TO ADJUST THE BELT If the pedals slip while you are pedaling, even while the resistance is adjusted to the highest setting, the belt may need to be adjusted. To adjust the belt, first carefully pry off the right Disc Cover (41) using a flat screwdriver. Next, remove the four screws (not shown) from the center of the right Disc (40). Gently rotate the Disc away from the elliptical exerciser. 41 40 Loosen, but do not remove, the three indicated screws (A). Insert the shaft of a 57 screwdriver B downward C between the A Idler (B) and the Idler Pulley (C). Pull the top of the screwdriver toward the front of the elliptical exerciser until the Belt (57) is tight. Then, tighten the three screws. Reattach the right disc with the four screws and then reattach the right disc cover. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
20
Inspect and tighten all parts of the elliptical exerciser
regularly. Replace any worn parts immediately.
To clean the elliptical exerciser, use a damp cloth and
a small amount of mild soap.
Important: To avoid
damage to the console, keep liquids away from
the console and keep the console out of direct
sunlight.
HANDGRIP PULSE SENSOR TROUBLESHOOTING
•
Avoid moving your hands while using the handgrip
pulse sensor. Excessive movement may interfere
with heart rate readings.
•
Do not hold the metal contacts too tightly; doing so
may interfere with heart rate readings.
•
For the most accurate heart rate reading, hold the
metal contacts for at least 15 seconds.
•
For optimal performance of the handgrip pulse sen-
sor, keep the metal contacts clean. The contacts
can be cleaned with a soft cloth—
never use alco-
hol, abrasives, or chemicals to clean the con-
tacts.
HOW TO CALIBRATE THE RAMP
If the ramp is not functioning properly, the ramp may
need to be calibrated. To calibrate the ramp, hold
down the Start button and the Resistance increase
button for about 5 seconds until the display on the
console changes. Next, press the Start button once,
and then press the Ramp increase button. Then, two
dashes and the word RAMP will appear in the display.
The ramp is now calibrated.
HOW TO ADJUST THE BELT
If the pedals slip while you are pedaling, even while
the resistance is adjusted to the highest setting, the
belt may need to be adjusted.
To adjust the belt,
first carefully pry
off the right Disc
Cover (41) using
a flat screwdriver.
Next, remove the
four screws (not
shown) from the
center of the right
Disc (40). Gently
rotate the Disc
away from the
elliptical exerciser.
Loosen, but do
not remove, the
three indicated
screws (A). Insert
the shaft of a
screwdriver
downward
between the
Idler (B) and the
Idler Pulley (C).
Pull the top of the
screwdriver
toward the front
of the elliptical exerciser until the Belt (57) is tight.
Then, tighten the three screws.
Reattach the right disc with the four screws and then
reattach the right disc cover.
MAINTENANCE AND TROUBLESHOOTING
41
40
B
C
A
57