Dell PowerEdge HS5620 PowerEdge HS5620 Installation and Service Manual - Page 166

Steps, Next steps, Installing the right control panel

Get Dell PowerEdge HS5620 PDF manuals and user guides View all Dell PowerEdge HS5620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 166 highlights

2. Follow the procedure listed in the Before working inside your system. Steps 1. Route the control panel cable through the side wall of the system and slide the cable into the clip. NOTE: Route the cable properly to prevent the cable from being pinched or crimped. 2. Align and insert the right control panel in the slot on the system. 3. Connect the right control panel cable and the VGA cable to the connector on the system board. 4. Using the Phillips #1 screwdriver, tighten the screws that secure the right control panel to the system. NOTE: The numbers on the image do not depict the exact steps. The numbers are for representation of sequence. Figure 133. Installing the right control panel Next steps 1. Install the air shroud. 2. Install the drive backplane cover. 3. Follow the procedure listed in the After working inside your system. 166 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
2.
Follow the procedure listed in the
Before working inside your system
.
Steps
1.
Route the control panel cable through the side wall of the system and slide the cable into the clip.
NOTE:
Route the cable properly to prevent the cable from being pinched or crimped.
2.
Align and insert the right control panel in the slot on the system.
3.
Connect the right control panel cable and the VGA cable to the connector on the system board.
4.
Using the Phillips #1 screwdriver, tighten the screws that secure the right control panel to the system.
NOTE:
The numbers on the image do not depict the exact steps. The numbers are for representation of sequence.
Figure 133. Installing the right control panel
Next steps
1.
Install the air shroud
.
2.
Install the drive backplane cover
.
3.
Follow the procedure listed in the
After working inside your system
.
166
Installing and removing system components